Eaton Fuller Transmission Alignment Troubleshooting
Ομόκεντροι Ευθυγράμμιση του κιβωτίου ταχυτήτων στη μηχανή
Κοινές ανησυχίες που απορρέουν από την κακή ευθυγράμμιση
Άμεση slipout ταχυτήτων
Drive gear bearing failure
Πρόωρη φθορά εισόδου πολύσφηνο άξονα από πίσω πλήμνη των δύο συμπλέκτες πλάκας
Ομόκεντροι ευθυγράμμιση
Concentric alignment means that the engine and transmission must have a common axis. The purpose of this section is to set forth the procedures to use in checking for possible misalignment.
The basic instrument needed for taking readings is a taper pointed dial indicator. The accuracy of readings is essential for correcting alignment problems. Clean all surfaces thoroughly before proceeding.
Κατά τη λήψη των ακόλουθων ενδείξεων, περιστρέψτε τη μηχανή με το χέρι, do not crank the engine with starter. Remove spark plugs on gasoline engines, and release compression on diesel engines.
Σημείωση: Before dial indicating engine flywheel or flywheel housing, make sure engine crankshaft does not have excessive end-play. Αν το κάνει, accurate readings cannot be obtained. Place dial indicator finger against the flywheel. Force crankshaft back and forth with pry bar. If end-play movement exceeds maximum as specified by the engine manufacturer, θα πρέπει να διορθωθεί.
φθαρμένα περιβλήματα
Inspect for worn or fretted pilot on both the transmission clutch housing and the engine flywheel housing. το 1/4″ pilot lip of transmission clutch housing can wear into the flywheel housing either by transmission loosening up or after high mileage just from the road and engine vibration.
Any appreciable amount of wear on either part will cause misalignment and the part should be replaced.
Η φθορά γενικά θα βρεθεί από το 3:00 o’clock to 8:00 θέση ώρα.
Μηχανή σφονδύλου Στέγαση Pilot
Dial indicate the pilot or bore of the engine flywheel housing. Secure dial indicator to engine flywheel with tapered point against housing pilot. Περιστρέψτε βολάν με το χέρι. With chalk or soapstone, mark high and low points of indicator as it is being rotated.
The total runout will be the difference between the highest plus and minus readings. SAE maximum total runout for flywheel housing pilot is .008″ with No.1 and No.2 SAE housings.
Βολάν Pilot Bore
Πληκτρολογήστε δείχνουν πιλότος που φέρει οπή του σφονδύλου. With indicator secured to flywheel housing, move gauge finger to contact pilot bearing bore surface. Turn flywheel and obtain readings. SAE maximum total runout for the pilot bearing is .005″.
Μετάδοση περιβλήματος συμπλέκτη
The transmission clutch housing face and pilot cannot be checked accurately in the field without special measuring tools. Recommended maximum runout for the transmission clutch housing face and pilot is .003″ with SAE No.1 and No.2 housings.
Οποιος μέρος μετάδοσης θα πρέπει να έχετε το έχουμε! διαθέσιμο ίδια ημέρα της ναυτιλίας, Παγκόσμιος.
ΠΡΕΠΕΙ δωρεάν υποστήριξη από έναν από τους ειδικούς μας?