Giderme Eaton Transmission Gears və Shafts2019-04-10T15:00:48+00:00

Giderme Eaton Transmission Gears & Shafts

clashing Gears

Snubbing and clashing gears while shifting are frequent abuses to which unsynchronized transmissions are subjected. Light snubbing will do little damage. The real damage is done by the hard clash shift caused by engaging gears which are far out of synchronization. This can break pieces of metal from the ends of the clutching teeth. Clashing gears can be traced to one of three causes:

snubbed clutching gear teeth

Snubbed Clutching Gear Teeth

1. düzgün keçid

This applies to drivers who are not familiar with the shift pattern or have not learned the RPM spread between shifts.

2. mufta

Clashing when starting up in first or reverse gear can be caused by insufficient clutch clearance or a dragging clutch not releasing properly. This makes the transmission countershafts and mainshaft gears continue rotating while the clutch pedal is depressed. Clashing results when the nonrotating sliding clutch is forced to mesh with a rotating mainshaft gear. Double clutching during lever shifts will also reduce snubbing and clashing.

3. inertial Force

Countershafts və mainshaft dişli adətən almaq 3 qədər 5 clutch sərbəstləşmiş sonra saniyə fırlanan dayandırmaq üçün. mainshaft Ötürücü əvvəl mainshaft Ötürücü ilə bir clutch Ötürücü mesh cəhd zidd düşən səbəb olacaq vermir. ötürülməsi clutch əyləc və ya countershaft əyləc ilə təchiz deyilsə, Bu ötürülməsi ilkin cəlb cəhd əvvəl clutch pedalı əzici sonra bir neçə saniyə fasilə etmək lazımdır.

Manufacturing Marks

Sometimes gears are replaced or thought to be defective because of marks left on the gear by manufacturing processes. Bu blemishes, lakin, do not contribute to gear failure and the gear should not be replaced because of these marks.

hob Marks

hob marks

These are cutting marks or lines formed during the initial cutting of the gear teeth. Hob marks on the tooth face will be removed by the shaving process, but hob marks in the root of the tooth will most likely remain, and may be found even on gears with much wear on them.

Təraş Marks

shaving marks on gear

The shaving operation leaves distinct diagonal marks on the face of the gear tooth. These marks can be distinguished from scoring marks by the fact they are diagonal, while scoring marks are more nearly vertical. Most shaving marks are removed during normal gear operation.

Gear Lipping

Gear Lipping

Lipping ya shaving burrs, is the formation of “lips” at the tip of the gear teeth machining. Bu "dodaqlar" Ötürücü heç bir zərər edəcəyik.

Boş da Gear Rattle

Mainshaft gears are designed to have a specified amount of axial clearance which allows them to rotate freely on the mainshaft. The amount of clearance is governed by the use of washers. A kobud idling mühərrik vibrasiya bilərsiniz, causing the mainshaft gears to rattle as they strike mating gears. This condition can usually be cured by improving the idling characteristics of the engine. Tolerance washers may have to be changed to bring the axial gear clearance to within tolerance on high mileage units. See the service manual for procedure and specifications.

Shaft Twist və Kırılma

Failure of transmission shafts through fracturing or twisting is caused when stresses are imposed on them which are greater than they were designed to withstand. The main causes for these failures are:

  1. Düzgün clutching texnika.
  2. Ötürücü çox yüksək etibarən.
  3. lugging.
  4. kilidli əyləc ilə başlamaq üçün cəhd.
  5. Transmission used for application it was not designed to withstand.
  6. dəstək zaman dok daxil bumping.
  7. tənzimlənən 5-ci təkər düzgün montaj.
fractured mainshaft

Fractured Mainshaft
Ötürücü dişləri kimi, shafts may fracture as a result of fatigue or impact.

twisted mainshaft

Twisted Mainshaft
Loads not severe enough to cause shaft fractures may cause the shaft to twist.

Hər hansı ötürülməsi hissəsi biz var lazımdır! Eyni gün göndərmə mövcuddur, dünyada.

BİZİM ekspertlərdən biri PULSUZ DƏSTƏK lazımdır?

İNDİ ZƏNG ET
EMAIL ABŞ
İndi Button Call