Eaton Fuller Transmission Torque tövsiyələr

  1. Qul VALVE CAPSCREWS
    8-12 Lbs.-Ft., 1/4-20 Threads. Use Lockwashers.
  2. FRONT COVER CAPSCREWS BEARING
    35-45 Lbs.-Ft., 3/8-16 Threads.
  3. sTUDS
    60 Lbs.-Ft., 3/8-16 minimum, Driven Until Bottomed, 5/8-11 Threads.
  4. CLUTCH MƏNZİL NUTS
    5/8-18 Threads

    • Aluminum Housing:
      140-150 Lbs.-Ft (mazlı), With Nylon Locking Insert. Use Plain Flat Washer.
    • Iron Mənzil Cast:
      180-200 Lbs.-Ft Standard Nut. istifadə Lockwasher.
  1. YOKE LOCKSCREWS
    Konus məşğul qədər Hand By başladı, 35-45 Lbs.-Ft., 7/16-20 Threads, Secure with Lock Wire.
  2. LEVER MƏNZİL CAPSCREWS SHIFT
    35-45 Lbs.-Ft., 3/8-16 Threads.
  3. BAR MƏNZİL CAPSCREWS SHIFT
    35-45 Lbs.-Ft., 3/8-16 Threads.
  4. YOKE CAPSCREWS SHIFT RANGE
    50-65 Lbs.-Ft., 1/2-20 Threads, Secure with Lock Wire.
  5. RANGE CYLINDER SHIFT BAR NUT
    70-85 Lbs.-Ft., 5/8-18 Threads with Nylon Locking Patch. (610)6610 model, 60-75 Lbs.-Ft. 1/2-13 Threads, Lockwasher istifadə edin.)
Eaton Fuller ötürülməsi tork tövsiyələr
  1. IDLER SHAFT KURUYEMİŞ TƏRS
    50-60 Lbs.-Ft., (mazlı) 5/8-18 Threads with Nylon Locking Insert.
  2. DRIVE GEAR NUT
    250-300 Lbs.-Ft., 2-1/8-16 L.H. Threads, Clean Threads with Solvasol or Equivalent Stake 2 Places.
  3. CLUTCH MƏNZİL CAPSCREWS
    1/2-13 Threads

    • Aluminum Housing:
      70-80 Lbs.-Ft., Use Shakeproof Internal Lockwasher.
    • Iron Mənzil Cast:
      80-100 lbs. Ft. istifadə Lockwasher
  4. C’SHAFT FRONT BEARING RETAINER CAPSCREWS
    20-25 Lbs.-Ft., 3/8-24 və ya 25-35 Lbs.-Ft., 1/2-20 Threads, Secure with Lock Wire 90-120 Lbs.-Ft., 5/8-18 Threads.
  1. üçün. DRIVE GEAR Qonorar CAPSCREWS BEARING
    35-45 Lbs.-Ft., 3/8-16 Threads. Secure with Lock Wire.
  2. OIL DRAIN PLUG
    45-55 Lbs.-Ft., 3/4 Pipe Threads
  3. AZALDILMASI / Splitter YOKE LOCKSCREW
    35-45 Lbs.-Ft., 7/16-20 Threads. Secure with Lock Wire.
  4. AUXILIARY MƏNZİL CAPSCREWS
    35-45 Lbs.-Ft., 3/8-6 Threads. Use Lockwashers.
  5. ÇIXDI SHAFT NUT
    450-500 Lbs.-Ft., (Oiled at Vehicle Installation). 2-16 Threads with Nylon Locking Insert. (vasitə quraşdırılması göt)
  1. SUPPORT STUD NUTS
    170-185 Lbs.-Ft., (Oiled at Vehicle Installation). 5/8-18 Threads, Use Lockwashers
  2. SUPPORT STUD
    60 Lbs.-Ft., minimum. Drive Until Bottomed 5/8-11 Threads.
  3. REAR COVER CAPSCREWS BEARING
    35-45 Lbs.-Ft., 3/8-16 Threads, Use Lockwashers.
  4. REAR COVER ESLOK CAPSCREWS BEARING
    35-45 Lbs.-Ft., 3/8-16 Threads, Use Brass Flat Washer & Nylon Collar.
  1. TƏRS SIGNAL SWITCH PLUG
    35-50 Lbs.-Ft., 9/6-18 Threads.
  2. AIR FILTER / REGULATOR CAPSCREWS
    8-12 Lbs.-Ft., 1/4-20 Threads.
  3. üçün. RANGE CYLINDER CAPSCREWS
    35-45 Lbs.-Ft., 3/8-16 Threads.
  4. üçün. RANGE CYLINDER COVER CAPSCREWS
    35-45 Lbs.-Ft., 3/8-16 Threads.
Eaton Torque Features
  1. AZALDILMASI / Splitter CYLINDER COVER CAPSCREWS
    20-25 Lbs.-Ft., 5/16-18 Threads.
  2. AZALDILMASI / Splitter CYLINDER PLUG
    40-50 Lbs.-Ft., 5/8-18 Threads.
  3. böyük P.T.O. COVER CAPSCREWS
    50-60 Lbs.-Ft., 7/16-14 Threads.
  4. OIL doldurun PLUG
    35-45 Lbs.-Ft., 1-1/4 Pipe Threads.
  1. HAND HOLE COVER CAPSCREWS
    20-25 Lbs.-Ft., 5/16-18 Threads.
  2. Sayğac MƏNZİL PLUG
    35-50 Lbs.-Ft., 13/16-20 Threads.
  3. termocüt PLUG
    40-50 Lbs.-Ft., 1/2 Pipe Threads.
  4. üçün. C’SHAFT REAR BEARING COVER CAPSCREWS
    35-45 Lbs.-Ft., 3/8-16 Threads.
  5. SMALL P.T.O. COVER CAPSCREWS
    35-45 Lbs.-Ft., 3/8-16 Threads.

Hər hansı ötürülməsi hissəsi biz var lazımdır! Eyni gün göndərmə mövcuddur, dünyada.

BİZİM ekspertlərdən biri PULSUZ DƏSTƏK lazımdır?

İNDİ ZƏNG ET
EMAIL ABŞ