Driveline անկյունավորություն Troubleshooting

torsional Տատանում

Ստուգում driveline U-համատեղ շահագործման անկյունները

Ակցիան է driveline ունիվերսալ համատեղ, այնպես էլ վերջում աշխատանքային միջոցով տեսանկյունից արդյունքների յուրատեսակ շարժման. Որ driveline կարագացնի եւ դանդաղեցնել երկու անգամ յուրաքանչյուր հեղափոխության. Եթե ​​աշխատանքային անկյունները կամ վերջում լիսեռ են անհավասար, torsional թրթռում արդյունքները. Այս torsional թրթռում կլինի հակված են չեղյալ հայտարարել իրեն դուրս, եթե երկու համատեղ աշխատանքային անկյունները հավասար են.

Տեսակները Noise

Աղմուկը կամ թրթռումային որը տեղի է ունենում միայն որոշակի ճանապարհային արագությամբ եւ նվազեցնում է որպես արագությամբ ավելանում է, ընդհանուր առմամբ, պայմանավորված է անհավասար աշխատանքային անկյունները Driveline հոդերի. Աղմուկը կամ թրթռումային, որը համառ ողջ արագությամբ միջակայք եւ տատանվում է ինտենսիվության փոփոխության հետ արագությամբ կարող է պայմանավորված լինել անհավասարակշռված drivelines, անհավասարակշիռ արգելակման հարվածային կամ սկավառակներով, կամ drivelines հետ համամարդկային հոդերի դուրս փուլի.

նախնական չեկերի

Դարձնել ստուգումներ է հետեւյալ նախքան անկյան ընթերցումներ:

  1. Check companion flange or yoke nut for looseness and torque to proper specification if necessary.
    Driveline slip համատեղ
  2. Driveline slip joints that do not have the arrows or other markings pointing to each other will result in the driveline universal joints being out of phase. Այլ կերպ ասած, the transmission universal joint may be turned one spline or more to the right or left of being aligned with the universal joint at the opposite end of the driveline.
    • Some computer designed drivelines are purposely built with U-joints out of phase. Check manufacturer’s specifications for proper setting. նույնպես, check closely to make certain no twist has occurred to the tubing, causing these two joints to be out of phase Make sure the slip joint works freely and is not bound or seized. Slip joints must absorb axle housing movements.
  3. Unbalanced drivelines can cause vibration that occurs throughout the speed range of vehicle and varies in intensity with a change of speed. The driveline may be at fault in respect to balance and concentricity. A quick field check to determine driveline balance can be made by securing a small piece of metal or similar weight with a hose clamp to the front of the tube where the splined shaft is welded. Road test the vehicle and continue to move the weight around the tube until the balance point is found and vibration disappears or is minimized.
    անհավասարակշիռ Driveline
    Drivelines դինամիկ հավասարակշռված իրենց նախատեսված պտտվող արագություն եւ ոչ թե անվերջ արագությամբ. այսպիսով, vibration can be expected when this rotational velocity is exceeded. Check concentricity of driveline by mounting on lathe centers and dial indicating. Ստուգեք արտադրողի տեխնիկական runout նպաստի.
  4. Engine աջակցում որոնք մաշված, կոտրված կամ չամրացված, and mounting pads that are worn or deteriorated must be corrected to restore the engine suspension to its original vibration tolerance.

հաշվի առնելով ընթերցումներ

plain, wing and flange driveline joint
plain driveline joint
universal joint

Take readings with protractor from machined surfaces of yokes or companion flanges. պարզ, wing կամ եզր տիպի միացումներ կարող են հանդիպել. Some will require partial disassembly to obtain accurate readings.

Ին պարզ տիպի հոդերի, it may be necessary to remove the bearing cap. Երբ հաշվի ընթերցումներ, make sure the universal joint is in a vertical plane. At the rear axle, take readings from a machined surface differential carrier that is in the same plane as the axle pinion shaft, կամ machined մակերեսի է, որ ուղղահայաց փետուր լիսեռ, թե որն է ավելի հեշտ է.

Եթե ​​թրթռում տեղի է ունենում, իսկ գործող դատարկ, take readings in empty condition. Եթե ​​դա տեղի է ունենում այն ​​ժամանակ, երբ բեռնված, take readings when loaded. When it is necessary to measure driveline lengths, measure from joint center to joint center

Արտադրողի մասնագրերը պետք է հետեւել, երբ կատարելու նախնական անկյունավորություն ստուգում. Some manufacturers have found it necessary to vary from the ideal due to geometrical limitations. If vibration persists after adhering to manufacturer’s specifications, contact the manufacturer’s representative.

Անկյունավորություն չեկերի - Զուգահեռ Կցաշուրթեր կամ Yokes

  1. Միայնակ Axle Տրանսպորտ
    • Փոխանցման տուփ անկյունը – Take reading of transmission angle. This angle is the angle to which the rear axle joint angle must match. The transmission angle will have a declination reading of from 0 դեպի 5 աստիճանով շատ դեպքերում.
      փոխանցման անկյունը ընթերցում
    • Առանցք անկյունը. Take reading either from machined surface of axle housing or pinion bearing retainer. This angle must be within one degree of the transmission angle.
      • Օրինակ: If transmission angle reading is 3 degrees down to the rear, the rear axle angle should be 3 աստիճանից մինչեւ.
  2. Tandem Axles կամ Տրանսպորտ Օժանդակ միավորների
    • Վերցրեք փոխանցման անկյան reading.
    • Take reading from joint of front tandem axle or auxiliary joint. This reading should be within one degree of transmission angle.
      • Նշում: The rear joint of front tandem axle will be the same as the front joint.
    • Վերցրեք ընթերցումը համատեղ անկյան ժամը Տանդեմ թիկունքում Axle, or axle to rear of auxiliary. This angle must be within one degree of transmission angle.

Համատեղ աշխատանքային Անկյուն Limits (Զուգահեռ)

Ունիվերսալ հոդերի ունենալ առավելագույն աշխատանքային տեսանկյունից, կախված տեսակից եւ արտադրության. Այն խորհուրդ է տրվում, որ համատեղ աշխատանքային անկյունը զուգահեռ համատեղ հավաքների չի գերազանցի 8 աստիճաններ համար հիմնական drivelines ավելի քան 40″ երկար. Համար հիմնական drivelines տակ 40″ իսկ առավելագույն անկյունը չպետք է գերազանցի Length (L) բաժանված 5. (Այս սահմանափակումը չի տարածվում այն ​​interaxle drivelines.)

Օրինակ: Համար 35″ Driveline, the maximum joint working angle would be 35 գումարած 5 կամ 7degrees. This working angle must not be exceeded.

Place protractor on driveline to obtain angle of driveline from transmission to axle. The difference between the driveline angle and the joint angle is the joint working angle. For instance, եթե փոխանցման 3 աստիճանից ցած, and the driveline angle is down 7 աստիճանով, the transmission joint working angle is 7 մինուս 3 կամ 4 աստիճանով.
Վրա Տանդեմ drive կամ օժանդակ սարքերի, take readings in the same manner, comparing the universal joint angles to the driveline angle to which it is attached.

Angularity Checks – Non-Parallel Compensating Angles or Flanges or Yokes

Կարճ անիվի բազան տրանսպորտային միջոցներով, որոնք ունեն նվազագույն driveline երկարությունը ից փոխանցման սռնու, որ driveline պահանջվում է գործել միջոցով շատ ծանր աշխատանքային անկյուններից որոշ սարքերի. Սա նաեւ վերաբերում է interaxle drivelines. Սրանք ծանր համատեղ աշխատանքային անկյունները դրդել թրթռում. Է նվազեցնել աշխատանքային անկյունները, այն առանցքը թեքված է դեպի վեր, մինչեւ փետուր լիսեռ centerline եւ փոխանցման mainshaft centerline հատվում մեջտեղում համատեղ կենտրոնների.

angularity check

Հետ տանդեմը drive axles, the rearward axle is tilted upward until its pinion shaft centerline and forward axle pinion shaft centerline intersect midway between joint centers.

Երբ figuring ոչ զուգահեռ համատեղ տեղակայմանն, it is necessary to take the driveline angle readings as well as transmission and axle angle readings.

  1. Միայնակ Axle Տրանսպորտ
    • Վերցրեք անկյան ընթերցումը փոխանցման
    • Վերցրեք տեսանկյունից Driveline
    • Վերցրեք անկյան ընթերցումը կամրջակներով համատեղ
    • Է հաշվարկել համար ճիշտ անկյուններից:
      • The difference between the driveline angle and the transmission angle will be the transmission joint working angle.
      • The difference between the driveline angle and the axle angle will be the axle joint working angle.
      • The two working angles of transmission and axle must be equal.
      • Օրինակ:
        փոխանցման 3 աստիճանից ցած
        driveline է 7.5 աստիճանից ցած
        Թիկունքն Axle 12 աստիճանից ցած
        այսպիսով 7.5 մինուս 3 հավասար 4.5 աստիճանով
        12 մինուս 7.5 հավասար 4.5 աստիճանով, giving 4.5 equal working angles
  2. Tandem Axles կամ Տրանսպորտ Օժանդակ միավորների – When taking readings on tandem drive axles or between auxiliary and rear axle, the same principles apply as with single axle vehicles. Take readings between transmission and front tandem axle, or auxiliary. Take readings between axles or between auxiliary and axle. Այլ կերպ ասած, take angle readings for each set of universal joints

Համատեղ աշխատանքային Անկյուն Limits (Ոչ Զուգահեռ)

Այն խորհուրդ է տրվում, որ առավելագույն համատեղ աշխատանքային անկյունը ոչ զուգահեռ համատեղ հավաքների չպետք է գերազանցի հիմնական driveline երկարությունը բաժանված 10. Օրինակ, եթե հիմնական Driveline երկարությունը ` 55, իսկ առավելագույն համատեղ աշխատանքային անկյունը 55 բաժանված 10 կամ 5.5 աստիճանով. (Այս սահմանափակումը չի տարածվում այն ​​interaxle drivelines.)

Axle ճշգրտում

Axle անկյունները կարող է ընդհանուր առմամբ կարելի է ճշգրտվում է մեկի հետեւյալ ձեւերով, կախված տեսակից սռնու.

  1. Կարգավորել ոլորող մոմենտ ձողերով, եթե կարգավորվող տեսակի.
  2. Add to or reduce length of non-adjustable torque rods.
  3. Add or reduce the number of shims behind torque rod brackets.
  4. Use correct amount of wedge shims under spring to axle pad.

Առկախման - փետուր լիսեռ Անկյուն

Կլինեն քիչ կամ ոչ մի փոփոխություն կամրջակներով փետուր անկյան հետ տեսակի կախույթների, որոնք ունեն զուգահեռագծի շարժում. Դրանք թույլ են տալիս դիֆերենցիալ պատյաններ շարժվել վեր ու վար է ուղիղ ուղղահայաց ընթացքում շահագործման.
Առկախման չունեցող զուգահեռագիծ շարժում, որը թույլ կտա կամրջակի փետուր լիսեռ է տատանվել է ՇՊՌԿ, դրանով անընդհատ փոփոխվող փետուր լիսեռ տեսանկյունից ընթացքում շահագործման. A տարբեր գումարը թրթռում կարող է առաջանալ հետեւանքով առաջացած աշխատանքային անկյունները համամարդկային հոդերի լինելու վայրկենապես անհավասար.
Միայնակ Կամուրջ Axle մեքենաների քիչ կամ ոչ մի փոփոխություն կամրջակի փետուր տեսանկյունից ընթացքում շահագործման.

Համար ձեռնարկներ եւ այլ ազատ ռեսուրսների համար խնդրում ենք այցելել մեր downloads էջը

փոխանցման ձեռնարկներ PDF

դիագրամների, Ձեռնարկներ եւ պահեստամասեր PDF ձեւաչափով >>>

Ցանկացած փոխանցման մաս դուք պետք մենք ունենք այն! Նույն օրը առաքման առկա, աշխարհահռչակ.

Պետք է ազատ ԱՋԱԿՑՈՒԹՅՈՒՆ Է մեկը մեր ՄԱՍՆԱԳԵՏՆԵՐԻ?

ԶԱՆԳԻՐ ՀԻՄԱ
ուղարկել մեզ էլեկտրոնային նամակ