Hybrid Eaton Fuller Gudbinta Babaca Code 60 – CAN Isgaarsiinta Link (Gudiga sare)

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. Read hoose si aad u bartaan sida si ay u tijaabiso, nadiifiso iyo hagaajin qalad code qalad aad Freightliner, Mack, Peterbilt, Kenworth, Volvo, International, iyo gaari xamuul culus-waajib iyo qalabka. Area Network maamusha The (CAN) waa-xawaaraha sare 500K labada ciyaaryahan qaloocin link xogta lahaansho ah oo isku xira HCM si Lidka Electric ah leewarka (ECA), Battery Control Module iyo Inverter. link The ka mid ah waxaa ku jira 120 Ohm resistor dhamaadka kasta. link waxaa loo isticmaalaa in ay u gudbiyaan macluumaad gaar ah si ay u xajin hawlgallada jago ama awood korantada.

khalad Code 60 – CAN Isgaarsiinta Link (Gudiga sare) ogaanshaha

The shuruud soo socda waa in la buuxiyaa ka hor inta nidaamka ogaadaa gardarrada:

  • Hybrid Control Module Gudiga sare waa ku shaqeeya oo danab suuroggalaan ka wada weyn yahay 7 volts iyo ka yar 16 volts.

Note: Marka dhib code ah Wax qabad la'aan tixraac ah Product Baarista Mode (PDM)

Xaaladaha in Calan Babaca Code Active

  • IMF 9 ayaa lagu wadaa markii HCM lumiyo isgaarsiinta oo dhan modules on link xogta CAN ee 30 farriimo isku xigta ama ka badan.
  • IMF 2 ayaa lagu wadaa in Product Baarista Mode (PDM) when the CAN loses communication with the HCM for 3 farriimo isku xiga

Uugu Marka Babaca Code 60 ayaa lagu wadaa shuruudaha soo socda dhici:

  • Red "Stop Hybrid" illuminates light.
  • Gaf waxa lagu kaydiyaa xasuusta HCM.
  • mode Operation badala in hab "AutoShift oo keliya".
  • Haddii qalad ah oo dhigaya at kor xoog, the engine will not crank.
  • Electric Motor / Generator la taageero iyo noolaynta naafada ah; si kastaba ha ahaatee, Relays a high-voltage sii powered.
  • Haddii nooc gardarrada halka baabuur-wadidda, the clutch will either close or open and remain in this position until fixed.
  • la bixin kari Gudbinta bilaabi marsho in 1aad.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay karaa Unit Gudbinta Electronic Control ah (TECU) ama taariikhda HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu ka dib markii taariikhda 200 saacadood iyo HCM si toos ah oo ansixiyay unu ka soo taariikhda ka dib qalad uu Wax qabad la'aan, waayo, 200 saacadood.

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • IMF 2, 9
    • Xogta Link CAN
    • Gudiga sare

khalad Code 60 – CAN Isgaarsiinta Link (Gudiga sare) Test

Aqoonsiga Qeybta:

HCM - Hybrid System Interface Connector

La habeeyo Front View
(Gudiga sare – Hybrid System Wajahadda isku xira)

Eaton Fuller transmission 9 pin diagnostic connector

9 Pin Baarista isku xira

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

Fuller HCM CAN 9 pin diagnostic connector

STEP 1. Hubi sii wareeggeedii Baarista isku xira.

  1. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  2. Key off.
  3. Cabir iska caabin ah u dhexeeya mid ka mid ah kuwan soo socda:
    • Pin H iyo Pin J on the 9-Jidka isku xira.
    • Pin A iyo B Pin on 3-Jidka isku xira.
    • pin 1 iyo Pin 2 on 2-jidka isku xira.
      Note: The 3-Way and 2-Way Data Link Connectors are located next to the 9-Way Diagnostic Connector.
      Note: Hubi in Waat / Ohm Meter waa on qiyaasta saxda ah (ku dhowaad 200 qiyaasta Ohm).

      • Haddii iska caabin ah oo u dhexeeya Pin H iyo J Pin, Pin A iyo B Pin, ama Pin 1 iyo Pin 2 waa inta u dhaxaysa 50 si ay u 70 ohms, tag Tallaabada 2.
      • Haddii iska caabin ka badan yahay 70 ohms, mid ama ka badan resistors gabagabaynta on Link Data CAN ee la habeeyo waa mid ka maqan ama ka duwan, ama waxaa jira furan in link. Dayactir OEM CAN Data Link la habeeyo, ka dibna tag Tallaabada 5.
      • Haddii iska caabin yar tahay 50 ohms, waxaa jira joogo resistor gabagabaynta dheeraad ah. Dayactir ka OEM CAN Data Link la habeeyo, ka dibna tag Tallaabada 5.

STEP 4. Hubi sii haddii Vehicle la habeeyo wareeggeedii J1939.

  1. Key off.
  2. Goostay cable batari negative.
  3. Barkinta HCM la habeeyo 38-Jidka isku xira.
  4. Cabir iska caabin ah oo u dhexeeya Gudiga la habeeyo 38-Jidka isku xira Pin 27 iyo Pin 28:
    Note: Hubi in Waat / Ohm Meter waa on qiyaasta saxda ah (ku dhowaad 200 qiyaasta Ohm).

    • Haddii iska caabin ah oo u dhexeeya Pin 27 iyo Pin 28 waa inta u dhaxaysa 110-130 ohms, bedeli Control Module ku Hybrid (Gudiga sare), ka dibna tag Tallaabada 3.
    • Haddii iska caabin ah ka baxsan ee kala duwan, dhiso CAN Data Link la habeeyo, ka dibna tag Tallaabada 3.

STEP 3. Hubi dayactirka.

  1. Key off.
  2. Key on.
  3. codes Clear, arki Unu qabad la'aan Clear.
  4. Xidhmaan oo dhan Xidhiidhiyayaasha iyo cable ka batari negative.
  5. Wado baabuur iyo isku dayaan in ay dib code ka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan.
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Code qalad 60 u muuqataa, heli qalad in imtixaanka, tag Tallaabada 1.
    • Haddii code kale oo aan ahayn 60 u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US