Hybrid Eaton Fuller Gudbinta Babaca Code 54 – DC / DC Converter Output danab

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. Read hoose si aad u bartaan sida si ay u tijaabiso, nadiifiso iyo hagaajin qalad code qalad aad Freightliner, Mack, Peterbilt, Kenworth, Volvo oo gaari International. The Converter DC / DC ku xiran Power Electronics Carrier ah (PEC), kaas oo bixiya 340 volts DC. danab waa la dhimay ilaa 12-volts DC oo uu xusay in nidaamka 12-volt lagu jiro engine off hawlgalka PTO. DC / DC waxay leedahay joogto ah 14.2 (± 0.2) (MY08 Systems) ama 12.6 (System MY09) volts saarka iyo kordhisaa amperage la baahida gaariga ilaa 1.5 kw ama 120 amps.

khalad Code 54 – DC / DC Converter danab Output Ogaanshaha

The shuruud soo socda waa in la buuxiyaa ka hor inta nidaamka ogaadaa gardarrada:

  • Control Module Hybrid (Gudiga sare) danab suuroggalaan waa ka weyn yahay 7 volts iyo ka yar 16 volts.

Note: Marka dhib code ah Wax qabad la'aan tixraac ah Product Baarista Mode (PDM)

Xaaladaha in Calan Babaca Code Active

  • IMF 2 ayaa lagu wadaa markasta / DC signal warcelin danab DC akhriya ka weyn tahay 15 volts ama ka yar 10 mode volts iyo ePTO ayaa ku hawlan.
  • IMF 4 ayaa lagu wadaa haddii warcelin danab uu ka yar yahay 15 volts iyo ka weyn 10 volts iyo farqiga u dhexeeya warcelin danab iyo danab batari gaari ka wada weyn yahay 0.5 volts waayo, 1 labaad ama ka badan.

Uugu Marka Babaca Code 54 ayaa lagu wadaa shuruudaha soo socda dhici:

  • Amber "Check Hybrid" illuminates light.
  • Gaf waxa lagu kaydiyaa Control Module Hybrid (Gudiga sare) xusuusta.
  • High-danab Motor / Generator caawi waa la heli karaa, laakiin at cadad la yareeyey.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay karaa Unit Gudbinta Electronic Control ah (TECU) ama taariikhda HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu ka dib markii taariikhda 200 saacadood iyo HCM si toos ah oo ansixiyay unu ka soo taariikhda ka dib qalad uu Wax qabad la'aan, waayo, 200 saacadood.

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • IMF 2
    • Danab silig celinta ka DC / DC Converter in HCM
  • IMF 4
    • 12-fiilooyinka awood volt ka batari 12-volt u Converter DC / DC ee
    • Power sahayda si HCM

khalad Code 54 – Danab Test DC / DC Converter Output

Aqoonsiga Qeybta:

HCM - Hybrid System Interface Connector

La habeeyo Front View
(Gudiga sare – Hybrid System Wajahadda isku xira)

Fuller transmission Deutsch 4-way OEM connector

Deutsch 4-jid isku xira OEM

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

HCM DCDC converter connector location

STEP 1.Verify status firfircoon ama qabad la'aan code qalad iyo hadiyad FMIs.

  1. Dib u eeg oo raaca digniinaha & ganaaxyada.
  2. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  3. Key off.
    Danger: Eeg High-Voltage Service Shutdown and Power-Up Procedures. Raac habraaca si looga fogaado filaan ah, gubaan ama dhimasho ka khaldan u maareeyeen a high-voltage.
  4. Waa kuwee FMIs joogaan?
    • Haddii FMI 2 waxaa ku qoran, tag Tallaabada 2.
    • Haddii FMI 4 waxaa ku qoran, tag Tallaabada 3.

STEP 2.Verify danab ka DC / DC Converter in HCM.

  1. Key off
  2. Dooro ePTO Mode on Pushbutton ama wareeg Lever.
  3. danab Cabbirka ee Converter DC / DC 12-volt boosteejada Output:
    • Haddii danab waa ka weyn yahay 10 volts, cusboonaysiiyo xambaarka furan ama shorted ka Pin 1 oo ka mid ah Converter DC / DC si Pin 19 ee Gudiga sare ee, ka dibna tag Tallaabada 5.
    • Haddii danab ka yar tahay 10 volts, badalo Converter DC / DC, ka dibna tag Tallaabada 5.

STEP 3. Hubi DC / DC Converter danab saarka.

  1. Key on.
  2. Connect ServiceRanger in 9-Jidka isku xira Baarista ee cab.
  3. View the following Data Monitor parameters in neutral:
    • PID 121 "DC / DC danab Output Converter."
    • PID 165 "Danab la fili karo Battery."
      • If voltage at the DC/DC Converter is 12–14 volts, tag Tallaabada 4.
      • Haddii danab waa ka baxsan kala duwan, cusboonaysiiyo xambaarka furan ama fiyuus in Main Power Supply ka Converter DC / DC si Battery 12-Waat ah. Tag Tallaabada 5.

STEP 4. Hubi danab ee Converter DC / DC.

  1. Key on.
  2. View soo socda oo xuduudaheedu Data Monitor:
    • PID 121 "DC / DC danab Output Converter."
    • PID 165 "Danab la fili karo Battery."
      • Haddii PID 165 waa 0.5 volts ka yar PID 121, lagu dhiso ama lagu badalo DC / DC Converter Power Supply la habeeyo in awoodaha System Battery 12-Waat ah, ka dibna tag Tallaabada 5.
      • Haddii PID 121 waa 0.5 volts ka yar PID 165, cusboonaysiiyo silig warcelin danab in uu ka Pin ah 1 oo ka mid ah Converter DC / DC si Pin 19 ee Gudiga sare ee. Tag Tallaabada 5.

STEP 5. Hubi dayactirka.

  1. Key off.
  2. Key on.
  3. codes Clear, arki Unu qabad la'aan Clear.
  4. Xidhmaan oo dhan Xidhiidhiyayaasha iyo cable ka batari negative.
  5. Wado baabuur iyo isku dayaan in ay dib code ka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan.
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Code qalad 54 u muuqataa, heli qalad in imtixaanka, tag Tallaabada 1.
    • Haddii code kale oo aan ahayn 54 u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US