Hybrid Eaton Fuller Gudbinta Babaca Code 52 – Gear Jago sensor

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. Read hoose si aad u bartaan sida si ay u tijaabiso, nadiifiso iyo hagaajin qalad code qalad aad Freightliner, Mack, Peterbilt, Kenworth, Volvo, iyo gaari xamuul ah International. The Rail Jago sensor waa shidma booska Hall Saamaynta ah in talo-bixin siinaysaa booska uu ka farta shaqada. The Unit Gudbinta Electronic Control (TECU) samatabbixiyaa tixraac 5-volt joogto ah si ay u 1 terminal ee Jago Tareenka ee sensor. wax soo saarka The signal ka shidma waxay bixisaa signal a danab nidaamsan ka 0.5-4.5 volts. terminal ugu danbeysay ee bixisaa dhulka ah Rail Jago shidma inay TECU ah.

khalad Code 52 – Gear Jago sensor Ogaanshaha

The shuruud soo socda waa in la buuxiyaa ka hor inta nidaamka ogaadaa gardarrada:

  • TECU danab suuroggalaan waa ka weyn yahay 7 volts iyo ka yar 16 volts.
  • IMF 3, 4 ma dhigay ma haddii qalad System TECU Battery Low danab waa Active. IMF 2 ma dhigay haddii FMI 3, 4 waa Active.

Note: Marka dhib code ah Wax qabad la'aan tixraac ah Product Baarista Mode (PDM)

Xaaladaha in Calan Babaca Code Active

  • IMF 2 dhigaya marka xakamaysada gudbinta ogaadaa ee danab Rail sensor waa kor ku xusan 4.5 volts ama ka hooseeya 0.5 volts waayo, 1 labaad ee dambe.
  • IMF 3 dhigaya marka xakamaysada gudbinta ogaadaa danab ku siin Rail sensor waa 5% kor ku xusan danab la filayo siin waayo, 1 labaad ama ka badan.
  • IMF 4 dhigay markii xakamaysada gudbinta ogaadaa danab ku siin Rail sensor waa 5% hoos danab la filayo siin waayo, 1 labaad ama ka badan.

Uugu Marka Babaca Code 52 ayaa lagu wadaa shuruudaha soo socda dhici:

  • Red "Service" illuminates iftiinka iyo dareenka gubashada ah "F" soo bandhigay marsho ah.
  • Gaf waxa lagu kaydiyaa xasuusta TECU.
  • Haddii qalad ay taasi dhacdo inta uusan u dhaqaaqin, gudbinta ayaa weli ku jira marsho hadda iyo xajin furo markii gaariga joojiyo.
  • mode Operation badala in "AutoShift uugu" mode.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay karaa Unit Gudbinta Electronic Control ah (TECU) ama taariikhda HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu ka dib markii taariikhda 200 saacadood iyo HCM si toos ah oo ansixiyay unu ka soo taariikhda ka dib qalad uu Wax qabad la'aan, waayo, 200 saacadood.

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • IMF 2
    • gudbinta la habeeyo
    • Rail Jago sensor
    • TECU
  • IMF 3, 4
    • TECU

khalad Code 52 – Gear Jago sensor Test

Aqoonsiga Qeybta:

Harness Front View TECU - Vehicle Interface Connector

La habeeyo Front View
(TECU – System Wajahadda isku xira)

Gear Position Sensor Pins

sensor heerkulka
(la habeeyo View – Side Front)

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

TECU rail position sensor connector location

STEP 1. Hubi xaaladda code qalad Active ama qabad la'aan.

  1. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  2. Key off.
  3. Waa kuwee FMIs joogaan?
    • Haddii FMI 3 ama 4 waxaa ku qoran, bedeli Unit Gudbinta Electronic Control ah (TECU), ka dibna tag Tallaabada 5.
    • Haddii FMI 2 waxaa ku qoran, tag Tallaabada 2.

STEP 2. Hubi sii wareeggeedii shidma Gudbinta la habeeyo.

  1. Key off.
  2. Goostay cable batari negative.
  3. Disconnect the Transmission Harness 38- isku xira Jidka.
  4. Cabir iska caabin ah oo u dhexeeya Gudbinta la habeeyo 38-Jidka isku xira musmaarradii:
    • 18 iyo 19
    • 18 iyo 20
      Note: auto-ka bilowda Waat digital ah / Ohm Meter waa in la isticmaalaa.

      • Haddii Pin 18 iyo Pin 19 caabin waa 100-200 ohms iyo haddii Pin 18 iyo Pin 20 caabin waa 5K-7K ohms, tag Tallaabada 3.
      • Haddii mid ka mid ah xaaladaha kor ku xusan aan la buuxin, tag Tallaabada 4.

STEP 3. Hubi sii wareeggeedii shidma Gudbinta lagaga dhulka.

  1. Measure resistance between Transmission Harness 38- Jidka isku xira Pin 18 si ay dhulka.
    • Haddii iska caabin ah waa 10km ohms ama ka weyn, bedeli Unit Gudbinta Electronic Control ah (TECU) (Oo kaliya haddii Babaca Code waa Active), ka dibna tag Tallaabada 5.
    • Haddii iska caabin yar yahay 10km ohms, tag Tallaabada 4.

STEP 4. Hubi sii Bannaanka Gudbinta la habeeyo Gear Jago sensor.

  1. Goostay Gudbinta la habeeyo ka Rail Select sensor.
  2. Cabir iska caabin ah oo u dhexeeya socda Rail Select sensor musmaarradii:
    • A iyo C
    • A iyo B
      Note: auto-ka bilowda Waat digital ah / Ohm Meter waa in la isticmaalaa.

      • Haddii Pin A iyo iska caabin Pin C waa 5K-7K iyo haddii Pin A iyo iska caabin Pin B waa 100-200 ohms, bedeli la habeeyo Gudbinta ah, ka dibna tag Tallaabada 5.
      • Haddii mid ka mid in shuruudaha kor ku xusan oo aan la kulmay, bedeli Electric Shifter, ka dibna tag Tallaabada 5.

STEP 5. Hubi dayactirka.

  1. Key off.
  2. Dib isugu xir dhammaan xiriiriyeyaasha iyo xarkaha batteriga taban.
  3. Key on.
  4. codes Clear, arki Unu qabad la'aan Clear.
  5. Wado baabuur iyo isku dayaan in ay dib code ka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan.
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Code qalad 52 u muuqataa, heli qalad in imtixaanka, tag Tallaabada 1.
    • Haddii code kale oo aan ahayn 52 u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US