Hybrid Eaton Fuller Gudbinta Babaca Code 35 – J1939 Isgaarsiinta Link (TECU)

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. 1939 waa-xawaaraha sare qaloocin labada ciyaaryahan 250K link xogta la mid ah 120 Ohm resistor dhamaadka kasta oo ka mid link. The Unit Gudbinta Electronic Control (TECU) ku xiran link xogta J1939 ee 38-Jidka isku xira. link waxaa loo isticmaalaa in macluumaadka si Control Module ku Hybrid gudbiyaan (Gudiga sare) iyo sidoo kale ula xiriiraan ama data ka modules kale ee network sida Unit Control Electronic ah ka helaan (ECU).

khalad Code 35 – J1939 Isgaarsiinta Link (TECU) ogaanshaha

The shuruud soo socda waa in la buuxiyaa ka hor inta nidaamka ogaadaa gardarrada:

  • TECU danab suuroggalaan waa ka weyn yahay 7 volts iyo ka yar 16 volts.
  • Gaf TECU Battery Low danab waa qabad la'aan.

Xaaladaha in Calan Babaca Code Active

  • IMF 2 ayaa lagu wadaa markii TECU lumiyo isgaarsiinta oo dhan modules on link xogta J1939 ee 5 ama ilbiriqsi ka badan.

Uugu Marka Babaca Code 35 ayaa lagu wadaa shuruudaha soo socda dhici:

  • Red "Service" illuminates iftiinka iyo dareenka gubashada ah "F" soo bandhigay marsho ah.
  • Gaf waxa lagu kaydiyaa xasuusta TECU.
  • The isbedel hab qalliin in hab AutoShift uugu.
  • Haddii qalad ah oo dhigaya at kor xoog, the engine will not crank.
  • Haddii nooc gardarrada halka baabuur-wadidda, gaariga ayaa weli ku jira marsho hadda iyo xajin furo marka xawaaraha baabuurta soo dhawaado oo aan waxtar lahayn.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay karaa Unit Gudbinta Electronic Control ah (TECU) ama taariikhda HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu ka dib markii taariikhda 200 saacadood iyo HCM si toos ah oo ansixiyay unu ka soo taariikhda ka dib qalad uu Wax qabad la'aan, waayo, 200 saacadood.

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • IMF 2
    • J1939 Data Link
    • TECU

khalad Code 35 – J1939 Isgaarsiinta Link (TECU) Test

Aqoonsiga Qeybta:

Eaton transmission Front Harness View TECU - Vehicle Interface Connector

Front la habeeyo View
TECU – Vehicle Wajahadda isku xira

Fuller 9-way Diagnostic Connector

9-Jidka isku xira Baarista

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

TECU to 9 way diagnostic connector for Eaton Fuller transmission

STEP 1. Hubi xaaladda code qalad Active ama qabad la'aan.

  1. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  2. Key on.
  3. Dooro screen "Vehicle ka Kooban" iyo aragto modules kala duwan warbixinta ku saabsan link J1939 ah:
    • Haddii TECU uusan warbixinta J1939, laakiin Gudiga sare waxaa ku qoran, tag Tallaabada 2.
    • Haddii Gudiga sare ee TECU midna waxaa ka warbixinta ku saabsan J1939, tag Tallaabada 3.

STEP 2. Hubi sii wareeggeedii Wajahadda Vehicle.

  1. Key off.
  2. Goostay cable batari negative.
  3. Disconnect TECU Vehicle Harness 38- jidka isku xira.
  4. Measure resistance between TECU Vehicle Harness 38- Jidka isku xira Pin 2 iyo Pin 3:Note: Hubi in Waat / Ohm Meter waa on the
    Note: Hubi in Waat / Ohm Meter waa on qiyaasta saxda ah (ku dhawaad ​​miisaanka 200ohm).

    • Haddii iska caabin ah oo u dhexeeya Pin 2 iyo Pin 3 waa inta u dhaxaysa 50-70 ohms, bedeli Unit Gudbinta Electronic Control (TECU), ka dibna tag in aan xoojinno 5.
    • Haddii iska caabin ah ka baxsan ee kala duwan, cusboonaysiiyo link Data J1939 ee la habeeyo, ka dibna tag Tallaabada 5.

STEP 3. Hubi sii Gudbinta la habeeyo isku xira ogaanshaha.

  1. Key off.
  2. Cabir iska caabin ah oo u dhexeeya isku xira ogaanshaha 9-Jidka Pin C iyo iska caabin Pin D.If dhexeeya Pin C iyo D waa Pin u dhexeeya 50-70 ohms, tag Tallaabada 4.
    • Haddii iska caabin ah waa 70 ohms ama ka weyn, mid ama ka badan resistors gabagabaynta on Link Data J1939 ee la habeeyo ka maqan yahay ama ka duwan, ama waxaa jira furan in link. Tag Tallaabada 5.
    • Haddii iska caabin ah waa 50 ohms ama ka yar, waxaa jira joogo resistor gabagabaynta dheeraad ah. Dayactir ka OEM J1939 Data Link la habeeyo, ka dibna tag Tallaabada 5.

STEP 4. Hubi sii Gudbinta la habeeyo wareeggeedii isku xira ogaanayo dhulka.

  1. Key off.
  2. Cabir iska caabin ah u dhexeeya soo socda 9- Jidka isku xira Baarista musmaarradii:
    • Pin C dhulka ku
    • Pin D dhulka
      • Haddii iska caabin ah oo u dhexeeya Pin C inay dhulka iyo Pin D dhulka ku jira labadaba 10km ohms ama ka weyn, isku dayaan in ay ula xiriiraan baabuur kale si loo hubiyo in ServiceRanger ayaa ka shaqaynaysa. Haddii ServiceRanger ku guuldareysto inuu la gaari kale oo isgaadhsiin, wac 1-800-826-HELP (4357).
      • Haddii iska caabin ah ka baxsan ee kala duwan, cusboonaysiiyo Data J1939 Link la habeeyo marka la soo gaabiyo ah dhulka, ka dibna tag Tallaabada 5.

STEP 3. Hubi dayactirka.

  1. Key off.
  2. Dib isugu xir dhammaan xiriiriyeyaasha iyo xarkaha batteriga taban.
  3. Key on.
  4. codes Clear, arki Unu qabad la'aan Clear.
  5. Wado baabuur iyo isku dayaan in ay dib code ka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan.
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Code qalad 35 u muuqataa, heli qalad in imtixaanka, tag Tallaabada 1.
    • Haddii code kale oo aan ahayn 35 u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US