Eaton Fuller Code Babaca Hybrid 16 – High Integrity Link (dilaan) Test

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. Integrity High The Link (dilaan) waa a-xawaaraha sare ee labada ciyaaryahan qaloocin 500K link xogta lahaansho isku xira Unit Gudbinta Electronic Control ah (TECU) si Control ku Riix badhanka Shift (PBSC). module kasta oo ku jira resistor 120-Ohm gudaha. HIL wuxuu xanbaarsan yahay macluumaad sida xulashada habka darawalka iyo eed macluumaad oo daari ah
"Service" light.

khalad Code 16 – High Integrity Link (dilaan) ogaanshaha

The shuruud soo socda waa in la buuxiyaa ka hor inta nidaamka ogaadaa gardarrada:

  • TECU danab suuroggalaan waa ka weyn yahay 7 volts iyo ka yar 16 volts.
  • System TECU Battery Low danab Babaca waa qabad la'aan.
  • TECU qaabeynta interface darawal ayaa lagu wadaa inuu HIL.

Xaaladaha in Calan Babaca Code Active

Xaaladaha in Calan Babaca:
• IMF 2 ayaa lagu wadaa markii TECU lumiyo isgaarsiinta 5 seconds ama in ka badan oo leh PBSC ah.

Uugu Marka Babaca Code 16 ayaa lagu wadaa shuruudaha soo socda dhici:

  • An "F" u muuqataa in qaab marsho ah.
  • Riix widhwidha Button Mode Light soo socota si ay hab la doortay iyo "Service" iftiin weli off.
  • nalalka Button riix on yimaadaan oo markaas weli off haddii link xogta ku guuldareysto at kor xoog.
  • Gaf waxa lagu kaydiyaa xasuusta TECU.
  • isbeddel hab Operation in hab AutoShift uugu.
  • Haddii code waa Active inta lagu jiro kor u awood, gudbinta ma galaan marsho ah.
  • If the fault is Active while driving, gudbinta ayaa weli ku jira marsho hadda. Waxaa markaas Doodu inay jaanta default mar gaariga joojiyo. Lidka furmay at ula taagtaagan iyo xirtey haddii ceejinta la cadaadisay. Gaariga guuro galay marsho default bilowga kaliya.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay kartaa taariikhda TECU ama HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu taariikhda ka dib 200 saacadood. Gudiga ayaa si toos ah oo ansixiyay unu taariikhda ka dib qalad uu noqdo mid aan firfircooneyn 200 saacadood.

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • IMF 2
    • Dili Data Link
    • PBSC
    • TECU
    • Power Supply la habeeyo ka TECU in PBSC

khalad Code 16 – High Integrity Link (dilaan) Test

Aqoonsiga Qeybta:

Fuller Harness Front View TECU - Vehicle Interface Connector

Fuller la habeeyo Front View
TECU – Vehicle Wajahadda isku xira

Eaton Harness Front View Push Button Shift Control Connector

La habeeyo Front View
Button riix wareejin Control isku xira

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

Eaton Fuller transmission TECU PBSC connection

STEP 1. Hubi xaaladda code qalad Active ama qabad la'aan.

  1. Dib u eeg oo raaca digniinaha & ganaaxyada.
  2. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  3. 3. Key on and observe the red Push Button “Service” light.
    • Haddii "Service" nuurka cas sano, tag Tallaabada 3.
    • Haddii "Service" nuurka cas ma shid, tag Tallaabada 2.

Step 2. Hubi voltages at Vehicle la habeeyo.

  1. Shift Control goostay 30-Jidka isku xira.
  2. Key on.
  3. danab qiyaas 30-Jidka isku xira dhexeeya Pin J3 iyo Pin C1.
    • Haddii danab gudahood waa 0.6 volts ee danab batari, tag Tallaabada 3.
    • Haddii out of kala duwan, tag Tallaabada 4.

Step 3. Hubi danab ee ka murugeeysan dib maamusha Shift Button.

        1. Key off
        2. Barkinta Button 30-Way ka murugeeysan dib ugu wareejin Control isku xira.
        3. Key on.
        4. Connect raadad voltmeter in Pin F1 iyo F2 Pin.
          Fiiro gaar ah * Hubi volt / meter Ohm waa on qiyaasta saxda ah; ku dhowaad 10 volts AC.

          • Haddii danab waa 0.10 volts AC ama ka weyn, bedeli Control Shift ah (oo kaliya haddii code qalad waa firfircoon), ka dibna tag in aan xoojinno 8.
          • Haddii danab waa out of kala duwan, tagaan in aan xoojinno 6.

STEP 4. Hubi sii ka Vehicle lagaga riix maamusha Shift Button.

    1. Key off
    2. Goostay cable batari negative.
    3. Goostay Vehicle la habeeyo 38-Jidka isku xira
      Note:       on Peterbilts, bandhigay marsho goostay
    4. Cabir iska caabin ah oo u dhexeeya:
      • Baddalo Control 30-Jidka isku xira Pin J3 iyo Vehicle la habeeyo 38-Jidka isku xira Pin 25.
        • Haddii iska caabin ah oo u dhexeeya Pin J3 iyo Pin 25 waa 0-0.3 ohms, tag Tallaabada 5.
        • Haddii mid ka mid ah xaaladaha kor ku xusan aan la buuxin, cusboonaysiiyo la habeeyo Vehicle u dhexeeya Control Shift iyo TECU, ka dibna tag Tallaabada 8.

STEP 5. Hubi sii ka wareeggeedii maamusha loosoo Shift Button dhulka.

    1. Key off
    2. Cabir iska caabin ka dhexeeya:
      • Shift Control 30-Way Connector Pin C1 and Vehicle Harness 38-Way Connector Pin 31.
      • Shift Control 30-Way Connector Pin C1 and ground.
    3. Haddii iska caabin ah oo u dhexeeya Pin C1 iyo Pin 31 waa 0-0.3 ohms iyo iska caabin ah oo u dhexeeya Pin C1 iyo dhulka waa 10km ohms ama ka weyn, replace Transmission Electronic Control Unit (TECU)(Oo kaliya haddii Babaca Code waa Active).
    4. Haddii mid ka mid ah xaaladaha kor ku xusan aan la buuxin, cusboonaysiiyo la habeeyo Vehicle u dhexeeya TECU iyo Control Shift, ka dibna tag Tallaabada 8.

Step 6. Hubi sii ka wareeggeedii maamusha loosoo Shift Button dhulka.

        1. Key off.
        2. Goostay cable batari negative.
        3. Goostay Vehicle la habeeyo 38-Jidka isku xira.
        4. Cabir iska caabin ah oo u dhexeeya:
          • Shift Control 30-Way Connector Pin F1 and Vehicle Harness 38-Way Connector Pin 28
          • Shift Control 30-Way Connector Pin F1 and ground.
        5. Haddii iska caabin ah oo u dhexeeya Pin F1 iyo Pin 28 is 0–0.3 ohms and if resistance between Pin F1 and ground is 10K ohms or greater, tag Tallaabada 7.
        6. Haddii mid ka mid ah xaaladaha kor ku xusan aan la buuxin, repair Vehicle Harness between the Shift Control and TECU, ka dibna tag Tallaabada 8.

Step 7. Hubi sii ka Vehicle lagaga riix maamusha Shift Button.

    1. Key off
    2. Cabir iska caabin ah oo u dhexeeya:
      • Baddalo Control 30-Jidka isku xira Pin F2 iyo Vehicle la habeeyo 38-Jidka isku xira Pin 27.
      • Shift Control 30-Way Connector Pin F2 and ground.
    3. Haddii iska caabin ah oo u dhexeeya Pin F2 iyo Pin 27 waa 0-0.3 ohms iyo iska caabin ah oo u dhexeeya Pin F2 iyo dhulka waa 10km ohms ama ka weyn, bedeli Unit Gudbinta Electronic Control (TECU)(Oo kaliya haddii Babaca Code waa Active). Tag Tallaabada 8.
    4. Haddii mid ka mid ah xaaladaha kor ku xusan aan la buuxin, cusboonaysiiyo la habeeyo Vehicle u dhexeeya Control Shift iyo TECU, ka dibna tag Tallaabada 8.

STEP 8. Hubi dayactirka.

  1. Key off.
  2. Dib isugu xir dhammaan xiriiriyeyaasha iyo xarkaha batteriga taban.
  3. Key on.
  4. codes Clear, arki Unu qabad la'aan Clear.
  5. Wado baabuur iyo isku dayaan in ay dib code ka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan.
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Code qalad 16 u muuqataa, heli qalad in imtixaanka, tag Tallaabada 1.
    • Haddii code kale oo aan ahayn 16 u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US