Kumbyuutarradeedu Test Eaton Fuller Gudbinta Hybrid Engine

imtixaanka calaamad-driven Tani waxaa la sameeyaa haddii a "N" waxaa soo bandhigay qaab marsho ah oo aan lahayn codes Active ama qabad la'aan iyo gaariga ma kumbyuutarradeedu.
The Control Module Hybrid (Gudiga sare) helo talooyin si kumbyuutarradeedu ka Pin 20 on the HCM 38-Jidka isku xira, kaas oo la banki ayaa si Switch Key. Gudiga sare sida caadiga ah awoodaha High-danab Motor / Generator si ay u bilaabaan engine ah. Haddii nidaamka hybrid waa offline, Gudiga sare u isticmaalo caadiga ah 12-volt starter by tamar Cranking 12-volt ee Relay. Relay Tani waxay markaas siisaa awood batari in Pin 30 of Start sahlo Relay, taas oo markaa awoodaha Solenoid bilowga.
Note: This symptom-based test should only be performed if directed here from the Diagnostic Procedure and there are no Active fault codes.

Eaton Fuller Gudbinta Hybrid Engine kumbyuutarradeedu Test Ogaanshaha

Calaamadaha soo socda waxaa laga yaabaa in lagu soo maray:

  • Vehicle ma kumbyuutarradeedu ama jiro adag "N" in Display ah Gear.

Sababaha macquulka ah

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • 12-Waat Cranking Relay
  • Bilaabin sahlo Relay
  • Vehicle la habeeyo
  • starter engine
  • 12-baytariyada volt
  • aqbasho Switch Key in Pin 20 ee Gudiga sare ee

Eaton Fuller Gudbinta Hybrid Engine kumbyuutarradeedu Test Qeybta Aqoonsiga

Fuller Harness Front View TECU - Vehicle Interface Connector

La habeeyo Front View
(TECU – Vehicle Wajahadda isku xira)

HCM - Hybrid System Interface Connector

La habeeyo Front View
(Gudiga sare – Hybrid System Wajahadda isku xira)

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

Eaton Fuller Hybrid Transmission TECU HCM Start Enable Relay Cranking Relay Truck Battery Connections

STEP 1. Arag dhawrtaan Display ah Gear ka dib xoog.

  1. Qabtaan imtixaanka calaamad this haddii oo kaliya haddii si toos ah inay sidaa sameeyaan by Baarista Index Calaamadaha-usoonoolaynta iyo ma jiraan codes qalad Active.
  2. Key on.
  3. N Press on Control ku Riix badhanka Shift:
    Note: The light ePTO waa in ay ahaadaan off marka la isticmaalayo biiro muhiimka ah si ay u bilaabaan gaariga.

    • Haddii "N" waa hadiyad soo bandhigay marsho ah, tag Tallaabada 2.
    • Haddii "N" ma joogo bandhigay marsho ah, tixraac ah "Habka Baarista Hybrid"Imtixaanka calaamad ku salaysan saxda ah si ay u qabtaan.

STEP 2. Hubi kumbyuutarradeedu Request dhimaya.

  1. Key on.
  2. Connect ServiceRanger in 9-Jidka isku xira Baarista.
  3. Select the “Data Monitor” option and view the “Crank Request” parameter:
    • Haddii Request kumbyuutarradeedu akhriya 1 (kumbyuutarradeedu), tag Tallaabada 3.
    • Haddii Request kumbyuutarradeedu akhriya 0 (No kumbyuutarradeedu), tag Tallaabada 5.

STEP 3. Hubi daacad ah Relay Cranking ah..

  1. Badallano bilow kala duwan awood iyo 12-volt Cranking Relay.
  2. Isku dayaan in ay kumbyuutarradeedu engine:
    • Haddii cranks engine, tilmaantid oo ka mid ah 2 Relays ayaa qalad kuna bedesho. Tag Tallaabada 6.
    • Haddii engine ma kumbyuutarradeedu, tag Tallaabada 4.

STEP 4. Hubi in awoodda Start sahlo Relay ah.

  1. Key on.
  2. Engine kumbyuutarradeedu laga yaabaa in.
  3. kicinta Pin 87 of Start sahlo Relay isku xira inay awood batari:
    • Haddii cranks engine, cusboonaysiiyo circuit furan dhexeeya Pin 87 of Start sahlo Relay iyo batari. U dir ka OEM waayo nidaamka dayactirka.
    • Haddii engine ma kumbyuutarradeedu, dareen waa la starter Solenoid ama Power lagaga Solenoid. U dir ka OEM waayo nidaamka dayactirka.

STEP 5. Hubi danab dhulka on HCM la habeeyo.

  1. Key off.
  2. Goostay cable batari negative.
  3. Barkinta HCM la habeeyo 38-Jidka isku xira.
  4. Key booska bilowga.
  5. Cabir danab ka HCM la habeeyo 38-Jidka isku xira Pin 20 si ay dhulka.
    • Haddii danab waa 11-13 volts, bedeli Control Module ku Hybrid (Gudiga sare), ka dibna tag Tallaabada 6.
    • Haddii danab hoose waa 11 volts, cusboonaysiiyo la habeeyo Vehicle ah, ka dibna tag Tallaabada 6.

STEP 6. Hubi dayactirka.

  1. Key off.
  2. Xidhmaan oo dhan Xidhiidhiyayaasha.
  3. Place Control Shift galay dhexdhexaad ah.
  4. Key on:
    • Haddii engine bilowday, baaritaanka waa complete.
    • Haddii engine ma bilaaban, heli qalad in imtixaanka, tag Tallaabada 1.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US