Eaton Fuller Babaca Code 4 motor / Sensor Speed ​​wareegga Generator

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. Sensor Speed ​​wareegga Motor / Generator waxaa Jaha danbe ee Motor / Generator ku wareegsan usheeda dhexe Input ah. shidma (design laba-piece) waa rotor ah dhajinta in Input usheeda dhexe iyo Ogaanshuhu Ring ah dhajinta in guryaha motor ka. Ogaanshuhu Ring waxaa bixisey low-danab lagu jiro hawlgalka. rotor jirsado jiraan is beddel danab galay Ring Ogaanshuhu ah, taas oo ka dibna beddelay signal a digital for RPM Motor / Generator. saarka danab iyo inta jeer ee uu hooseeyo at ula taagtaagan iyo kordhisaa la RPM.

khalad Code 4 – Motor sensor Speed ​​wareegga Generator / Ogaanshaha

  • danab suuroggalaan Inverter waa ka weyn yahay 7 volts iyo ka yar 16 volts.
  • IMF 2 ma dhigay ma haddii ay jirto Input Gudbinta Active qalad sensor Speed ​​usheeda dhexe ah.

Xaaladaha in Calan Babaca Code Active

Xaaladaha in Calan Faul Code Active:

  • IMF 0 ayaa lagu wadaa marka xawaaraha Motor / Generator ka badan heerka caadiga ah la ogolyahay.
  • IMF 2 ayaa lagu wadaa marka xawaaraha Motor / Generator waa ka duwan yahay Input Gudbinta usheeda dhexe Speed ​​ka badan 100 RPM ugu yaraan 10 seconds.
  • IMF 3: Set when the resolver circuit is shorted to ground.
  • IMF 21: Set when a resolver signal line short to 12-volt battery or ground is detected.
  • IMF 22, 24, 25 ayaa lagu wadaa markii isku dhafan ee calaamadaha Converter analog-to-digital waa jaanqaadayn a.
  • IMF 27 ayaa lagu wadaa markii Inverter helo qalad ah inta lagu guda jiro baaritaanka bilowga ah.
  • IMF 23 ayaa lagu wadaa marka uu jiro signal ah baadi saarka analog-to-digital Converter waayo, 100 MS.
  • IMF 26 ayaa lagu wadaa marka xawaaraha shidma wareeg ka wada weyn yahay 6000 min-1 10 MS.

Uugu Marka Babaca Code 4 ayaa lagu wadaa shuruudaha soo socda dhici:
• Amber "Check Hybrid" illuminates light.
• Babaca waxa lagu kaydiyaa Control Module Hybrid (Gudiga sare) xusuusta.
• Electric Motor/Generator Assist and Regeneration are disabled; si kastaba ha ahaatee, ee Relays a high-voltage sii powered.
• HCM continues to control the hybrid vehicle in a diesel-only mode.
• la bixin kari Gudbinta bilaabi marsho in 1aad.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay karaa Unit Gudbinta Electronic Control ah (TECU) ama taariikhda HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu ka dib markii taariikhda 200 saacadood. Gudiga ayaa si toos ah oo ansixiyay unu ka soo taariikhda ka dib qalad uu Wax qabad la'aan, waayo, 200 saacadood

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

MY08

  • IMF 0
    • fasalada kordhiyay muddada u baahan karaan isticmaalka goos ah taayarada adeegga si aad u yarayso gaariga
  • IMF 22, 24, 25, 27
    • Inverter
  • IMF 2, 23, 26
    • Inverter
    • Motor / Generator
    • Resolver la habeeyo dhexeeya Motor / Generator iyo Inverter

MY09

  • IMF 3, 21
    • Inverter
    • Resolver Harness between the motor/generator
      and Inverter
  • IMF 2, 22, 23, 24, 25, 27
    • Inverter
    • Motor / Generator
    • Resolver la habeeyo dhexeeya Motor / Generator iyo Inverter
    • Water in Inverter or Resolver wire connector

khalad Code 4 – Motor / Generator wareegga Speed ​​sensor Test

System Qeybta Aqoonsiga MY08:

Delphi 56-Way Mating Connector View

Delphi 56-Jidka isku xira rimay View

Eaton Transmission Resolver Harness View

Resolver la habeeyo View (Side Front)

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

Eaton Fuller Inverter motor generator resolver connection

System Qeybta Aqoonsiga MY09:

Deutsch 40-Way Mating Connector View

Deutsch 40-Jidka isku xira rimay View

Eaton Terminal Side - Harness Connector Resolver Deutsch 6-pin connector

Eaton Terminal Side – Harness Connector Resolver Deutsch 6-pin connector

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

Eaton invertor motor generator resolver MY09

STEP 1. Hubi xaaladda code qalad Active ama qabad la'aan.

  1. Dib u eeg oo raaca digniinaha & ganaaxyada.
  2. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  3. Key off.
    Danger: Eeg High-Voltage Service Shutdown and Power-Up Procedures. Raac habraaca si looga fogaado filaan ah, gubaan ama dhimasho ka khaldan u maareeyeen a high-voltage.
  4. Qabtaan korontada Pretest iyo Hybrid korontada Pretest. (MY09 only)
  5. Check Inverter part number. (MY09 Kaliya)
    • If Inverter is part number 4306453, contact Eaton Call Center at 1-800-826-HELP (4357)
  6. Waa kuwee FMIs joogaan?
    • MFIs 22, 24, 25, ama 27 waxay ku qoran yihiin, bedeli Inverter ah, ka dibna tag Tallaabada 4.
    • Haddii FMI 2, 23, ama 26 waxay ku qoran yihiin, tag Tallaabada 2.
    • Haddii FMI 3 ama 21 waxaa ku qoran, tag Tallaabada 6.
    • Haddii FMI 0 waxaa ku qoran, Using ServiceRanger select the Advanced Product Functions and download the TECU and HCM snapshots then contact Eaton at 1-800-826-HELP (4357) (MY08 only). Tag in aan xoojinno 7 (MY09 only).

STEP 2.Verify sii qaybaha Resolver iyo Inverter.

  1. Key off.
  2. Disconnect the Low-Voltage Connector at the Inverter.
  3. Inspect for water intrusion inside wire connector.
  4. (MY08 Kaliya) Cabir iska caabin Resolver ee la habeeyo 56-Jidka isku xira dhexeeya musmaarradii soo socda:
        • pin 55 in Pin 56
        • pin 53 in Pin 54
        • pin 51 in Pin 52

      Note: Si tartiib ah awooddiisa Inverter ee 56-Jidka isku xira la habeeyo dhow isku xira inta la socodka qiimaha caabiga.
      Resistance u dhaxeysa waayo, biinanka yihiin:

      • musmaarradii 55 in Pin 56: 10.5-8,6 ohms
      • musmaarradii 53 in Pin 54: 34-28 ohms
      • musmaarradii 51 in Pin 52: 27-23 ohms
    • Haddii resistances kor ku xusan waxaa laga helaa, iyo FMI 2 waa Active, contact Eaton at 1- 800-826-I CAAWI (4357).
    • Haddii resistances kor ku xusan waxaa laga helaa, iyo FMI 26 ama 23 waa Active, bedeli Inverter ah, ka dibna tag Tallaabada 4.
    • Haddii iska caabin ah ka baxsan ee kala duwan waxaa loogu talagalay mid ka mid ah ay akhrintu, tag Tallaabada 3.

4. (MY09 only) Determine if resistance for the Resolver at the 40-Way Harness Connector between the following pins is within the range listed:

  • pin 30 in Pin 40 is 8.6–10.5 ohms
  • pin 28 in Pin 38 is 28–34 ohms
  • pin 29 in Pin 39 is 23–27 ohms
    Note: An / meter auto-ka bilowda volt digital Ohm waa in la isticmaalaa.

    • Haddii iska caabin ah ka baxsan ee kala duwan waxaa loogu talagalay mid ka mid ah ay akhrintu, tag Tallaabada 5.
      • If resistance is within range, tag Tallaabada 3.

STEP 3. Hubi sii circuitry Resolver la habeeyo.

  1. Key off.
  2. Barkinta 6-Jidka Motor / Generator Resolver isku xira.
  3. (MY08 only) Cabir iska caabin Resolver ee la habeeyo 6-Jidka isku xira dhexeeya musmaarradii soo socda:
        • pin 5 in Pin 6
        • pin 1 in Pin 3
        • pin 2 in Pin 4

      Note: auto-ka bilowda Waat digital ah / Ohm Meter waa in la isticmaalaa.
      Resistance u dhaxeysa waayo, biinanka yihiin:

      • musmaarradii 5 in Pin 6: 10.5-8,6 ohms
      • musmaarradii 1 in Pin 3: 34-28 ohms
      • musmaarradii 2 in Pin 4: 27-23 ohms
    • Haddii resistances kor ku xusan waxaa laga helaa, cusboonaysiiyo suunka bannaan ee u dhexeeya isku xira Inverter 56-Jid oo Resolver Motor / Generator 6-Jidka isku xira, ka dibna tag Tallaabada 4.
    • Haddii iska caabin ah ka baxsan ee kala duwan, bedeli Motor / Generator ah, ka dibna tag Tallaabada 4.

3. (MY09 Kaliya) Measure Resolver resistance at the 40-Way Harness Connector between the following pins:

  • pin 38 in Pin 40
  • pin 38 in Pin 3
  • pin 28 in Pin 40
  • pin 28 in Pin 3
  • pin 28 si ay dhulka
  • pin 38 si ay dhulka
  • pin 30 si ay dhulka
  • pin 40 si ay dhulka
    • Haddii iska caabin ah u furan yahay ama OL, bedeli Inverter.
    • Haddii caabiga wax kale oo aan ahayn OL, tag Tallaabada 4.

STEP 4. (MY08 Kaliya) Hubi dayactirka.

  1. Key off.
  2. Xidhmaan oo dhan Xidhiidhiyayaasha iyo cable ka batari negative.
  3. Key on.
  4. codes Clear, arki Unu qabad la'aan Clear.
  5. Wado baabuur iyo isku dayaan in ay cilinta xeerka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Babaca Code 4 u muuqataa, la xiriir Eaton ee 1-800-826-HELP (4357).
    • Haddii code kale oo aan ahayn 4 u muuqataa, arki Khalad List Code Index.

STEP 4. (MY09 only) Hubi sii circuitry Resolver la habeeyo.

  1. Disconnect the 6-Way motor/generator Resolver Connector (the connector going into the motor).
  2. Cabir iska caabin Resolver ee la habeeyo 6-Jidka isku xira dhexeeya musmaarradii soo socda:
    Note: An / meter auto-ka bilowda volt digital Ohm waa in la isticmaalaa.

    • pin 1 in Pin 3
    • pin 1 in Pin 4
    • pin 2 in Pin 3
    • pin 2 in Pin 4
    • pin 1 si ay dhulka
    • pin 2 si ay dhulka
    • pin 3 si ay dhulka
    • pin 4 si ay dhulka
  3. Haddii iska caabin ah u furan yahay ama OL, repair wiring between Resolver and Inverter.
  4. Haddii caabiga wax kale oo aan ahayn OL, replace the motor/generator then go to Step 8.

STEP 5. (MY09 Kaliya) Measure resistance of Resolver circuit at motor/generator.

  1. Disconnect 6-Way Resolver wire connector at motor/generator.
  2. Determine if resistance on the following pins falls within the listed range:
    • pin 1 in Pin 2 is between 28–34 ohms
    • pin 3 in Pin 4 is between 8.6–10.5 ohms
    • pin 5 in Pin 6 is between 23–27 ohms
  3. Haddii iska caabin ah ka baxsan ee kala duwan, replace the motor/generator (Resolver is not serviceable). After repairs are made go to Step 8.
  4. If resistance is within range, repair wiring between Resolver and Inverter. After repairs are made go to Step 8.

STEP 6. (MY09 only) Verify the resistance at the Inverter.

    1. Key off
    2. Disconnect 40-Way Low Voltage Connector at the Inverter.
    3. Measure Resolver resistance at the 40-Way Har-ness connector between the following pins:
      • pin 28 in Pin 1
      • pin 28 in Pin 6
      • pin 29 in Pin 1
      • pin 29 in Pin 6
      • pin 38 in Pin 1
      • pin 38 in Pin 6
      • pin 39 in Pin 1
      • pin 39 in Pin 6
        Note: An / meter auto-ka bilowda volt digital Ohm waa in la isticmaalaa.
    4. If resistance is open or OL replace inverter. After repair is made go to Step 8.
    5. If resistance is anything other than OL go to H.

STEP 7. (MY09 Kaliya) Verify overspeed condition by test driving the vehicle.

  1. 1. Test drive vehicle to verify an overspeed condition. This may require a downhill road condition, verify with customer the road condition when fault was set.
    • Haddii FMI 0 is set in a true overspeed condition, vehicle will need to be slowed down to prevent overspeed condition.
    • Haddii ay suurtagal tahay, update HCM software version number 672 or higher. If vehicle has HCM with primary hardware version 4306455, the most current software version available is 663. To update software version 672 or higher requires an HCM with hardware version 4306473. Hardware version number can be found in Service Ranger under Product Configurations, Gudiga sare, Primary Hardware Version.

STEP 4. (MY09 Kaliya) Hubi dayactirka.

  1. Key off.
  2. Xidhmaan oo dhan Xidhiidhiyayaasha iyo cable ka batari negative.
  3. Key on.
  4. codes Clear, arki Unu qabad la'aan Clear.
  5. Wado baabuur iyo isku dayaan in ay cilinta xeerka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Babaca Code 4 u muuqataa, la xiriir Eaton ee 1-800-826-HELP (4357).
    • Haddii code kale oo aan ahayn 4 u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US