Eaton Fuller Code Babaca Hybrid 17 – Bilaabin sahlo Relay

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. Start The sahlo Relay waxaa banki galay Unit Gudbinta Electronic Control ah (TECU) dhinaca gariiradda ee Relay ah. At muhiim ah oo ku saabsan, HCM ay go'aamiso oo laga bilaabo si ay u isticmaalaan hab (A high-voltage Motor / Generator ama Engine starter). Haddii HCM isticmaasho bilowga engine caadiga ah, 12-volt ee Cranking Relay waxaa tamaraysan qeybinayay awood batari in Start sahlo Relay feed ugu weyn, taas oo markaa awoodaha Solenoid bilowga.

khalad Code 17 – Bilaabin sahlo Relay Ogaanshaha

The shuruud soo socda waa in la buuxiyaa ka hor inta nidaamka ogaadaa gardarrada:

  • Unit Gudbinta Control Electronic (TECU) danab suuroggalaan waa ka weyn yahay 7 volts iyo ka yar 16 volts.

Xaaladaha in Calan Babaca Code Active

  • IMF 3: TECU detects an open or short to VBATT in the control circuit of the Start Enable Relay for 1 labaad ama ka weyn.
    IMF 4: TECU detects a short to ground in the control circuit of the Start Enable Relay for 1 labaad ama ka weyn.

Uugu Marka Babaca Code 17 ayaa lagu wadaa shuruudaha soo socda dhici:

  • Red "Service" illuminates iftiinka iyo dareenka gubashada ah "F" soo bandhigay marsho ah.
  • Gaf waxa lagu kaydiyaa xasuusta TECU.
  • Haddii qalad ah oo dhigaya at awood kor engine weli cranks, haddii ay baytariyada a high-voltage leeyihiin State ku filan oo Charge (GOS).
  • Haddii nooc gardarrada halka baabuur-wadidda, gaariga sii wadaan in ay ku shaqeeyaan.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay kartaa taariikhda TECU ama HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu ka dib markii taariikhda 200 saacadood. Gudiga ayaa si toos ah oo ansixiyay Gaf taariikhda ka dib markii ay ka soo wareegtay Wax qabad la'aan, waayo, 200 saacadood.

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • IMF 3, 4
    • xiriir dabacsan ama mirdheen, musmaarradii laaban yihiin ama la gubo, gaaban dhulka, furan, ama gaaban oo VBATT on Bannaanka.
    • Bilaabin sahlo Relay
    • TECU

khalad Code 17 – Bilaabin sahlo Test Relay

Aqoonsiga Qeybta:

Harness Front View TECU - Vehicle Interface Connector

Front la habeeyo View
(TECU – Vehicle Wajahadda Connecto

Relay switch

Switch Relay caadiga ah

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

Eaton Fuller TECU start enable relay connection

STEP 1. Hubi xaaladda code qalad firfircoon ama aan firfircoonayn iyo hadiyad FMIs.

  1. Dib u eeg oo raaca digniinaha & ganaaxyada.
  2. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  3. Dhaafsadaan Start hadda loo sahlo Relay la Relay kale oo fiiriya hadday eed celinta:
    • Haddii eed ma leh Relay cusub kuma ay soo noqon, kubedel Start sahlo Relay (oo kaliya haddii code qalad waa Active), ka dibna tag Tallaabada 6.
    • Haddii qalad Laabtay la Relay cusub, tag Tallaabada 2.

STEP 2.Verify FMI set.

  1. Waa kuwee FMIs ayaa ku qoran oo ka Step 1?
    • Haddii FMI 3 waxaa ku qoran, tag Tallaabada 3.
    • Haddii FMI 4 waxaa ku qoran, tag Tallaabada 5.

STEP 3.Verify sii wareeggeedii Gudbinta la habeeyo.

  1. Key off.
  2. Goostay cable batari negative.
  3. Disconnect the Transmission Harness 38- jidka isku xira.
  4. Measure resistance between Vehicle Harness 38- Jidka isku xira Pin 32 iyo Pin 4:
    • Haddii iska caabin ah oo u dhexeeya Pin 32 iyo Pin 4 waa 40-120 ohms, tag Tallaabada 4.
    • Haddii iska caabin ah ka baxsan ee kala duwan, cusboonaysiiyo la habeeyo Vehicle ee wareeg furan, ka dibna tag Tallaabada 6.

STEP 4.Verify voltages at Gudbinta la habeeyo.

  1. Key on.
  2. danab Cabbirka dhexeeya Vehicle la habeeyo 38-Jidka isku xira Pin 32 iyo dhulka:
    Note: danab The akhriya 5 volts kaliya 1-2 seconds

    • Haddii danab u dhexeeya Pin 32 iyo dhulka waa 5 volts, bedeli Unit Gudbinta Electronic Control ah (TECU) (oo kaliya haddii code qalad waa Active), ka dibna tag Tallaabada 6.
    • Haddii danab u dhexeeya Pin 32 iyo dhulka waa 12 volts, cusboonaysiiyo gaaban si VBATT on xambaarka. Danab waa sii joogo 5 volts 1-2 ilbiriqsi ka dib markii muhiim ah bilowga ah ee. Tag Tallaabada 6.

STEP 5. Hubi sii wareeggeedii Gudbinta lagaga dhulka.

  1. Key off.
  2. cable batteriga ka furid.
  3. Disconnect the Transmission Harness 38- isku xira Jidka. Measure the resistance between Vehicle Harness 38- Jidka isku xira Pin 32 iyo dhulka:
    • Haddii iska caabin ka dhexeeya 32 iyo dhulka waa 10km ohms ama ka weyn, bedeli Unit Gudbinta Electronic Control ah (TECU) (oo kaliya haddii code qalad waa Active), ka dibna tag Tallaabada 6.
    • Haddii iska caabin ah ka baxsan ee kala duwan, cusboonaysiiyo la habeeyo Vehicle ee gaaban dhulka, ka dibna tag Tallaabada 6.

STEP 6. Hubi dayactirka.

  1. Key off.
  2. Dib isugu xir dhammaan xiriiriyeyaasha iyo xarkaha batteriga taban.
  3. Key on.
  4. codes Clear, arki Unu qabad la'aan Clear.
  5. Wado baabuur iyo isku dayaan in ay dib code ka.
  6. Hubi codes, arki View unu Active iyo Wax qabad la'aan.
    • Haddii codes ma, baaritaanka waa complete.
    • Haddii Code qalad 17 u muuqataa, heli qalad in imtixaanka, tag Tallaabada 1.
    • Haddii code kale oo aan ahayn 17 u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US