Eaton Fuller Code Babaca Hybrid 1 Motor Generator hadda sensor

Khalad code for Hybrid Eaton daydo Systems Drive (MY08) Cuneyso-8E306A-U, Cuneyso-8E306A-UPG, Cuneyso-8E306A-UP, Cuneyso-8E306A-CD, Cuneyso-8E306A-T, Cuneyso-6E606B-CD, (MY09) Cuneyso-8E406A-U / P, Cuneyso-8E406A-UP, Cuneyso-8E406A-UPG, Cuneyso-8E406A-CD, Cuneyso-8E406A-CDG, Cuneyso-8E406A-guud, Cuneyso-8E406A-T, Cuneyso-6E706B-CD, Cuneyso-6E706B-P iyo aad cuneyso-6E706B-UPG. The High-Voltage Motor/Generator Assembly is connected to the Inverter Assembly through an AC High-Voltage Cable that contains 3 fiilooyinka gaar ah. Inta uu hawlgalka socday, the Inverter monitors the amperage in the AC cables through a current sensor, kaas oo la Jaha gudaha Inverter ah. The inductive sensor produces an output based on amperage present in the cables.

khalad Code 1 Motor / Generator hadda sensor Ogaanshaha

danab suuroggalaan Inverter waa ka weyn yahay 7 volts iyo ka yar 16 volts.

Xaaladaha in Calan Babaca Code Active

Xaaladaha in Calan Babaca:

  • IMF 6 is set when Inverter detects current input from the Motor/Generator greater than 100 amps waayo, 150 MS.
  • IMF 0 is set when the Inverter detects current input from the Motor/Generator greater than 200 amps waayo, 0.3 MS.
  • IMF 15 is set when the sensor offset is out of range at initial check.

Uugu Marka Babaca Code 1 ayaa lagu wadaa shuruudaha soo socda dhici:
• Amber "Check Hybrid" illuminates light.
• Babaca waxa lagu kaydiyaa Control Module Hybrid (Gudiga sare) xusuusta.
• Electric Motor/Generator Assist and Regeneration are disabled; si kastaba ha ahaatee, ee Relays a high-voltage sii powered.
• HCM continues to control the hybrid vehicle in a diesel-only mode.
• la bixin kari Gudbinta bilaabi marsho in 1aad.

Xaaladaha in Calan Babaca Code qabad la'aan

Kaliya unu qabad la'aan la nadiifiyay karaa Unit Gudbinta Electronic Control ah (TECU) ama taariikhda HCM isticmaalaya ServiceRanger. TECU ayaa si toos ah oo ansixiyay unu ka dib markii taariikhda 200 hours and the HCM automatically clears the faults from history after the fault has stayed Inactive for 200 saacadood.

code qalad Tani waxaa keeni kara wax ka mid ah kuwan soo socda:

  • IMF 0, 6
    • Inverter
    • Motor / Generator
    • AC cable
  • IMF 15
    • Inverter

khalad Code 1 – Motor / Generator sensor Test hadda

System Qeybta Aqoonsiga MY08:

High-Voltage AC Harness Connector View

High-danab AC la habeeyo isku xira View
(Amphenol isku xira)

High-Voltage AC Motor/Gen Connector View

High-danab AC Motor / Gen isku xira View
(Amphenol isku xira)

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY08

component connector

System Qeybta Aqoonsiga MY09:

High-Voltage AC Harness Connector View

High-danab AC la habeeyo isku xira View
(Amphenol isku xira)

High-Voltage AC Motor/Gen Connector View

High-danab AC Motor / Gen isku xira View
(Amphenol isku xira)

FIIRO GAAR AH: U dir ka Eaton Qeybta Hybrid oo isku xira Location waayo, Goobaha isku xira in Systems MY09.

component connector

STEP 1. Hubi xaaladda code qalad iyo sii of circuitry a high-voltage.

  1. Dib u eeg oo raaca digniinaha & ganaaxyada.
  2. Ceshano codes qalad Active iyo FMIs la ServiceRanger isticmaalaya Baarista 9-Jidka isku xira.
  3. Key off.
    Danger: Eeg High-Voltage Service Shutdown and Power-Up Procedures. Raac habraaca si looga fogaado filaan ah, gubaan ama dhimasho ka khaldan u maareeyeen a high-voltage.
  4. Remove the AC Cable from the Motor/Generator and Inverter.
  5. Measure resistance of each circuit in the AC High-Voltage Cable Pins A-A, B-B iyo C-C:
    • If resistance for each circuit is less than 1 ohm, tag Tallaabada 2.
    • Haddii iska caabin ah ka baxsan ee kala duwan, badalo Cable AC High-danab, ka dibna tag Tallaabada 5.
    • Haddii FMI 15 waa Active, bedeli Inverter ah.

STEP 2. Hubi sii circuitry a high-voltage dhulka.

  1. Measure resistance of each circuit to ground in the AC High-Voltage Cable:
    • If resistance between each circuit and ground is 5M ohms or greater, tag Tallaabada 3.
    • Haddii iska caabin ah ka baxsan ee kala duwan, badalo Cable AC High-danab, ka dibna tag Tallaabada 5.

STEP 3. Hubi sii circuitry a high-voltage.

  1. Key off
  2. Measure the resistance between the following AC High-Voltage Cable Pins A-B, B-C iyo C-A(MY08 Systems) A-A, B-B, C-C (MY09 Systems):
    • Haddii iska caabin ah marxalad kasta waa 5 ama ka weyn, tag Tallaabada 4.
    • Haddii iska caabin ah ka baxsan ee kala duwan, badalo Cable AC High-danab, ka dibna tag Tallaabada 5.

STEP 4. Hubi sii weji Motor / Generator.

  1. Measure resistance of each Motor/Generator phase at the following Pins: A-B, B-C iyo C-A (MY08 Systems) / A-A, B-B, C-C (MY09 Systems):
    • If resistance of each phase is less than 10 ohms, bedeli Inverter ah, ka dibna tag Tallaabada 5.
    • Haddii iska caabin ah ka baxsan ee kala duwan, bedeli Motor / Generator ah, ka dibna tag Tallaabada 5.

STEP 5. Hubi dayactirka.

  1. Key off
  2. Xidhmaan oo dhan Xidhiidhiyayaasha iyo cable ka batari negative.
  3. Key on
  4. codes Clear
  5. Wado baabuur iyo isku dayaan in ay dib code ka.
  6. Hubi codes. Haddii codes ma, baaritaanka waa complete, Haddii Babaca Code 1 u muuqataa, heli qalad in imtixaanka, tag Tallaabada 1. Haddii code cusub u muuqataa, arki Khalad List Code Index.

Qof kasta oo gudbinta qayb aad u baahan tahay aynu u leeyihiin! maalin isku mid ah maraakiibta la heli karo, dunida oo dhan.

U BAAHAN TAAGEERO FREE KA MID khubaro OUR?

WAC NOW
email US