Eaton Fuller Code Fault Hybrid 1 Sensor Current Generator Motor

Qusûra code for Eaton Hybrid modelên Drive Systems (MY08) EH-8E306A-U, EH-8E306A-UPG, EH-8E306A-UP, EH-8E306A-CD, EH-8E306A-T, EH-6E606B-CD, (MY09) EH-8E406A-U / P, EH-8E406A-UP, EH-8E406A-UPG, EH-8E406A-CD, EH-8E406A-CDG, EH-8E406A-CDR, EH-8E406A-T, EH-6E706B-CD, EH-6E706B-P û EH-6E706B-UPG. The High-Voltage Motor/Generator Assembly is connected to the Inverter Assembly through an AC High-Voltage Cable that contains 3 kabloyên cuda. di dema operasyonê de, the Inverter monitors the amperage in the AC cables through a current sensor, e, ku di nava wan de bibîne siyar. The inductive sensor produces an output based on amperage present in the cables.

qusûra Code 1 Detection Generator Sensor / niha Motor

The voltaja dadana bibîne mezintir e 7 volt û kêmtir ji 16 volts.

Şert û mercên ji bo Set Code Fault Active

Şert û mercên ji bo Set Fault:

  • IMF 6 is set when Inverter detects current input from the Motor/Generator greater than 100 Amps ji bo 150 MS.
  • IMF 0 is set when the Inverter detects current input from the Motor/Generator greater than 200 Amps ji bo 0.3 MS.
  • IMF 15 is set when the sensor offset is out of range at initial check.

Dih Dema Code Fault 1 Biryar e ku şert û mercên li jêr pêk:
• Amber "Check Hybrid" ronîkirin ronahî.
• Fault di Modula Kontrola Hybrid profîlek (HCM) bîr.
• Electric Motor/Generator Assist and Regeneration are disabled; lebê, li peyamstînerî bilind-voltaja powered bimîne.
• HCM continues to control the hybrid vehicle in a diesel-only mode.
• vebijêrkên wê nifşek dest gear to 1st.

Şert û mercên ji bo Set Fault Code Neçalak

Tenê kêmasîyên Neçalak dikare ji Unit ji nifşek a Control Electronic kenîştê (TECU) an dîroka HCM bikaranîna ServiceRanger. The TECU automatically kiribin gonehên ji dîroka piştî 200 hours and the HCM automatically clears the faults from history after the fault has stayed Inactive for 200 saetan.

Ev koda sûcê dikare ji aliyê yek ji yên jêr ji ber:

  • IMF 0, 6
    • bibîne
    • Motor / Generator
    • cable AC
  • IMF 15
    • bibîne

qusûra Code 1 – Motor Generator Test / niha Sensor

System Component tespît MY08:

High-Voltage AC Harness Connector View

High-Voltage AC Harness Connector View
(Amphenol Connector)

High-Voltage AC Motor/Gen Connector View

High-Voltage AC Motor / Gen Connector View
(Amphenol Connector)

NOT: Bi xweşî hatî ferhenga Refer Eaton Component Hybrid û Connector Location ji bo Locations Connector li Systems MY08

component connector

System Component tespît MY09:

High-Voltage AC Harness Connector View

High-Voltage AC Harness Connector View
(Amphenol Connector)

High-Voltage AC Motor/Gen Connector View

High-Voltage AC Motor / Gen Connector View
(Amphenol Connector)

NOT: Bi xweşî hatî ferhenga Refer Eaton Component Hybrid û Connector Location ji bo Locations Connector li Systems MY09.

component connector

GAV 1. Check ji bo statûya code biqusûr û berdewamiya xwe ji circuitry bilind-voltaja.

  1. Review û li pey Hişyarî & kirêt.
  2. Şûnde codes sûcê Têketina û FMIs bi ServiceRanger bikaranîna 9-Way Diagnostic Connector.
  3. off Key.
    Talûke: Dîtin High-Voltage Girtin Service û Power-Up Rûtînên. Follow prosedurên ji dûr şokê, bişewitin an mirinê ji çewt bidome bilind-voltaja.
  4. Remove the AC Cable from the Motor/Generator and Inverter.
  5. Measure resistance of each circuit in the AC High-Voltage Cable Pins A-A, B-B û C-C:
    • If resistance for each circuit is less than 1 ohm, biçe Step 2.
    • Heke berxwedana e li derveyî range, li şûna Cable AC High-Voltage, paşê biçe Step 5.
    • Ger FMI 15 Active e, li şûna bibîne.

GAV 2. Piştrastkirina berdewamiya circuitry bilind-voltaja bo qirçandin.

  1. Measure resistance of each circuit to ground in the AC High-Voltage Cable:
    • If resistance between each circuit and ground is 5M ohms or greater, biçe Step 3.
    • Heke berxwedana e li derveyî range, li şûna Cable AC High-Voltage, paşê biçe Step 5.

GAV 3. Piştrastkirina berdewamiya circuitry bilind-voltaja.

  1. off Key
  2. Measure the resistance between the following AC High-Voltage Cable Pins A-B, B-C û C-A(Systems MY08) A-A, B-B, C-C (Systems MY09):
    • Heke berxwedana her qonaxa 5M an mezintir e, biçe Step 4.
    • Heke berxwedana e li derveyî range, li şûna Cable AC High-Voltage, paşê biçe Step 5.

GAV 4. Piştrastkirina berdewamiya xwe ji qonaxên Motor / Generator.

  1. Measure resistance of each Motor/Generator phase at the following Pins: A-B, B-C û C-A (Systems MY08) / A-A, B-B, C-C (Systems MY09):
    • If resistance of each phase is less than 10 Ohms, li şûna bibîne, paşê biçe Step 5.
    • Heke berxwedana e li derveyî range, li şûna Motor / Generator, paşê biçe Step 5.

GAV 5. Piştrastkirina repair.

  1. off Key
  2. , Îlhamek hemû connectors û cable battery neyînî.
  3. Key li ser
  4. kodên Clear
  5. Drive wesayîta û hewldana ji bo reset koda.
  6. Check bo codes. Ger tu kodên, test complete e, Ger Code Fault 1 xuya, bibînin error li testkirina, biçe Step 1. Heke koda nû xuya, dîtin Qusûra Lîsteya Index Code.

Herçiyek beşek ji nifşekî hûn divê em jî heye! heman rojê di shipping License de, cîhanê.

Bi piştgirîya ji ji pisporên?

BANGAWAZÎ NOW
Email Amerîka