Eaton Fuller Hybrid Kòd Fay 1 Machin Dèlko Kouran sensor

Fay kòd pou Eaton Hybrid modèl Drive Sistèm (MY08) EH-8E306A-U, EH-8E306A-UPG, EH-8E306A-UP, EH-8E306A-CD, EH-8E306A-T, EH-6E606B-CD, (MY09) EH-8E406A-U / P, EH-8E406A-UP, EH-8E406A-UPG, EH-8E406A-CD, EH-8E406A-CDG, EH-8E406A-CDR, EH-8E406A-T, EH-6E706B-CD, EH-6E706B-P ak EH-6E706B-UPG. The High-Voltage Motor/Generator Assembly is connected to the Inverter Assembly through an AC High-Voltage Cable that contains 3 câbles separe. pandan operasyon, the Inverter monitors the amperage in the AC cables through a current sensor, ki se monte andedan onduleur nan. The inductive sensor produces an output based on amperage present in the cables.

fay Kòd 1 Machin / Dèlko Kouran sensor Deteksyon

vòltaj la onduleur ignisyon gen plis pouvwa pase 7 vòlt ak mwens pase 16 vòlt.

Kondisyon yo mete Fay Kòd aktif

Kondisyon yo mete Fay:

  • Fon Monetè Entènasyonal 6 is set when Inverter detects current input from the Motor/Generator greater than 100 anp pou 150 MS.
  • Fon Monetè Entènasyonal 0 is set when the Inverter detects current input from the Motor/Generator greater than 200 anp pou 0.3 MS.
  • Fon Monetè Entènasyonal 15 is set when the sensor offset is out of range at initial check.

Fallback Lè Fay Kòd 1 is set the following conditions occur:
• Amber "Tcheke Hybrid" salum limyè.
• Fay se ki estoke nan Hybrid Modil Kontwòl (HCM) memwa.
• Electric Motor/Generator Assist and Regeneration are disabled; sepandan, rle yo segondè-vòltaj rete mache.
• HCM continues to control the hybrid vehicle in a diesel-only mode.
• défaut Transmisyon kòmanse Kovèti pou nan 1st.

Kondisyon yo mete Fay Kòd Inaktif

Se sèlman fot Inaktif ka otorize soti nan Inite a Transmisyon Elektwonik kontwòl (TECU) oswa istwa HCM lè l sèvi avèk ServiceRanger. TECU la otomatikman efase fot yo nan istwa apre 200 hours and the HCM automatically clears the faults from history after the fault has stayed Inactive for 200 èdtan.

Sa a kapab Kòd fòt ki te koze pa nenpòt nan sa ki annapre yo:

  • Fon Monetè Entènasyonal 0, 6
    • onduleur
    • Machin / Dèlko
    • AC kab
  • Fon Monetè Entènasyonal 15
    • onduleur

fay Kòd 1 – Machin / Dèlko Kouran sensor Tès

Component Idantifikasyon MY08 Sistèm:

High-Voltage AC Harness Connector View

High-Voltage AC Harness Connector Gade
(Amphenol Connector)

High-Voltage AC Motor/Gen Connector View

High-Voltage AC Machin / Gen Connector Gade
(Amphenol Connector)

REMAK: Gade nan nan Eaton Hybrid Component ak Connector Kote pou Connector Kote yo ye nan MY08 Sistèm

component connector

Component Idantifikasyon MY09 Sistèm:

High-Voltage AC Harness Connector View

High-Voltage AC Harness Connector Gade
(Amphenol Connector)

High-Voltage AC Motor/Gen Connector View

High-Voltage AC Machin / Gen Connector Gade
(Amphenol Connector)

REMAK: Gade nan nan Eaton Hybrid Component ak Connector Kote pou Connector Kote yo ye nan MY09 Sistèm.

component connector

ETAP 1. Tcheke pou estati Kòd fòt ak kontinite ki gen gwo-vòltaj sikui.

  1. Revize epi swiv nan avètisman & prekosyon.
  2. Rekipere kòd fòt aktif ak FMIs ak ServiceRanger lè l sèvi avèk Dyagnostik Connector a 9-Way.
  3. kle nan.
    danje: wè High-Voltage Service Shutdown and Power-Up Procedures. Swiv pwosedi yo pou fè pou evite chòk, boule oswa lanmò soti nan mal okipe segondè-vòltaj.
  4. Remove the AC Cable from the Motor/Generator and Inverter.
  5. Measure resistance of each circuit in the AC High-Voltage Cable Pins A-A, B-B ak C-C:
    • If resistance for each circuit is less than 1 ohm, ale nan Etap 2.
    • Si rezistans se deyò nan ranje, ranplase kab la AC segondè-vòltaj, Lè sa a, ale nan Etap 5.
    • Si FMI 15 se aktif, ranplase onduleur nan.

ETAP 2. Verify kontinwite nan segondè-vòltaj sikui nan tè.

  1. Measure resistance of each circuit to ground in the AC High-Voltage Cable:
    • If resistance between each circuit and ground is 5M ohms or greater, ale nan Etap 3.
    • Si rezistans se deyò nan ranje, ranplase kab la AC segondè-vòltaj, Lè sa a, ale nan Etap 5.

ETAP 3. Verify kontinwite nan segondè-vòltaj sikui.

  1. kle nan
  2. Measure the resistance between the following AC High-Voltage Cable Pins A-B, B-C ak C-A(MY08 Sistèm) A-Yon, B-B, C-C (MY09 Sistèm):
    • Si rezistans nan chak faz se 5M oswa pi plis, ale nan Etap 4.
    • Si rezistans se deyò nan ranje, ranplase kab la AC segondè-vòltaj, Lè sa a, ale nan Etap 5.

ETAP 4. Verify kontinwite nan Machin / Dèlko faz.

  1. Measure resistance of each Motor/Generator phase at the following Pins: A-B, B-C ak C-A (MY08 Sistèm) / A-Yon, B-B, C-C (MY09 Sistèm):
    • If resistance of each phase is less than 10 om, ranplase onduleur nan, Lè sa a, ale nan Etap 5.
    • Si rezistans se deyò nan ranje, ranplase Machin / Dèlko a, Lè sa a, ale nan Etap 5.

ETAP 5. Verify reparasyon.

  1. kle nan
  2. Rekonekte tout konektè ak kab sa a ki batri negatif.
  3. kle sou
  4. kòd Klè
  5. Kondwi machin nan ak eseye Reyajiste kòd la.
  6. Tcheke pou kòd. Si pa gen okenn kòd, tès se konplè, Si Fay Kòd 1 parèt, jwenn erè nan tès, ale nan Etap 1. Si yon kòd nouvo parèt, wè Fay Kòd Index Lis.

nenpòt pati transmisyon ou bezwen nou genyen li! Menm jou anbake disponib, atravè lemond.

BEZWEN GRATIS SIPÒ NAN youn nan ekspè NOU?

RELE kOUNYE A
imèl nou